Datasheet R01DS0371EJ0100 RL78/G1P Rev.1.00 RENESAS MCU Nov 29, 2019 True low-power platform (66 A/MHz, and 0.31 A for LVD) for the general-purpose and sensor control applications, with 2.7-V to 3.6-V operation, low pin counts (24 or 32 pins), small ROM capacity (16 Kbytes), and highly-functional analog circuits (12-bit A/D and 10-bit D/A converters) 1. OUTLINE 1.1 Features Minimum instruction execution time can be 8/12-bit resolution A/D converter (VDD = 2.7 to 3.6 changed from high speed (0.03125 s: 32 MHz V): 6 or 8 channels operation with high-speed on-chip oscillator) to Standby function: HALT, STOP, SNOOZE mode low-speed (1 s: 1 MHz operation with high- On-chip 10-bit D/A converter speed on-chip oscillator) DMA controller: 2 channels General-purpose registers: 8 bits 32 registers (8 On-chip event link controller (ELC) bits 8 registers 4 banks) Power supply voltage: VDD = 2.7 to 3.6 V ROM: 16 KB, RAM: 1.5 KB, Data flash: 2 KB Operating ambient temperature: TA = -40 to +85C High-speed on-chip oscillator (A: Consumer applications, D: Industrial Select from 32 MHz (TYP.), 24 MHz (TYP.), 16 applications) MHz (TYP.), 12 MHz (TYP.), 8 MHz (TYP.), 6 MHz (TYP.), 4 MHz (TYP.), 3 MHz (TYP.), 2 Remark The functions mounted depend on the MHz (TYP.), and 1 MHz (TYP.) product. See 1.6 Outline of Functions. On-chip single-power supply flash memory (with prohibition of block erase/writing function) Self-programming On-chip debug function On-chip power-on-reset (POR) circuit and voltage detector (LVD) On-chip watchdog timer (operable with the dedicated low-speed on-chip oscillator) On-chip clock output/buzzer output controller On-chip BCD adjustment I/O ports: 26 or 28 (N-ch open drain: 2) Timer 16-bit timer TAU: 4 channels Watchdog timer: 1 channel Serial interface CSI: 1 channel UART: 1 channel 2 I C 1 channel (2 slave addresses) R01DS0371EJ0100 Rev.1.00 Page 1 of 39 Nov 29, 2019 RL78/G1P 1. OUTLINE ROM, RAM capacities Note Flash ROM Data Flash RAM 24-pin 32-pin 16 KB 2 KB 1.5 KB R5F11Z7AANA, R5F11Z7ADNA R5F11ZBAAFP, R5F11ZBADFP Note The flash libraries use the on-chip RAM area from FFE20H to FFEFFH and the parts of the RAM area referred to as self RAM (RAM for use in self-programming), which are listed in the table below, for self-programming or rewriting of the data flash memory. See below for the RAM areas used by the flash library. RAM FSL Type01 FDL Type04 EEL Pack01, EEL Pack02 Self RAM size Self RAM size Note 896 bytes 136 bytes R5F11Z7AANA 1.5 KB FF900H to FFC7FH FF900H to FF987H Not available R5F11Z7ADNA R5F11ZBAAFP R5F11ZBADFP Note Functions supported in FSL Type01 are only basic functions. Other functions are not supported. Basic functions: FSL Init, FSL Open, FSL Close, FSL PrepareFunctions, FSL BlankCheck, FSL Erase, FSL IVerify, FSL Write, and FSL StatusCheck R01DS0371EJ0100 Rev.1.00 Page 2 of 39 Nov 29, 2019