RF600D

RF / IR Encoder / Decoder Chipset RF600E RF600D RF Evaluation Boards, Highly Secure Protocol RF Encoder & Decoder ICs Simple to Use Stand Alone Operation Achieves Maximum Range from RF Modules 1 4 Switch Options (15 states) Decoder Serial Output Led Indication of Transmission Directly Compatible with Keeloq Decoder Easy Learn Feature of Transmitters Sleep Mode Up to 48 Transmitters can be Learned Description Optimum Range: The RF Solutions RF600E, & RF600D are easy to use AM up to 100m encoder and decoder I/Cs. They have been designed to FM up to 200m achieve the maximum possible range from any radio / Infra IR up to 20m Red transmitter receiver set. Unlike other encoder /decoder devices the RF600E/600D Compatible with RF Solutions Systems provide an unprecedented level of security which prevents Typical Applications copying or grabbing whist also obtaining optimum range from the transmitter and receiver. General Purpose Remote Control The devices are very easy to use and can be inserted Automotive alarm systems directly into a circuit. The RF600D has an easy learn Gate and garage openers feature enabling it to learn up to 7 unique RF600E encoder devices in standalone mode or up to 48 encoder devices Electronic door locks when used in conjunction with an external EEPROM. Identity tokens These devices enable a simple but secure remote telemetry application whilst obtaining the maximum range Burglar alarm systems from the radio set. Encoder 2.0-6.6V operation 1 8 Automatic Battery Level Monitor 2 7 RF600E Manchester modulation 3 6 4 5 8 pin DIP/SOIC package 18 1 Decoder 2 17 18 pin DIP/SOIC package 16 3 4 Digital Outputs (15 States) 15 4 5 RF600D 14 Asynchronous serial interface 13 6 4.5V 5.5V operation 12 7 8 11 9 10 DS600-10 March 06 2004 Reg. No. 227 4001, ENGLAND Page 1 RF / IR Encoder / Decoder Chipset RF600E RF600D RF Evaluation Boards, Transmitter Encoder RF600E Operational Description The RF600E is a simple device to use. As shown in the typical application circuits, it requires only the addition of input switches and RF circuitry for use as the transmitter in the end application. Transmission is automatic without user intervention. The RF600E will wake up upon detecting a switch closure and then delay approximately 6.5 ms for switch debounce. The encrypted or hopping code portion of the transmission will change every time a button is pressed, even if the same button is pushed again. Achieving Optimum Range Range is dependant on many factors including 1. RF Power output 2. Receiver sensitivity 3. Antenna efficiency 4. Local environmental conditions and any local Interference 5. Data Type which is being transmitted. Whilst items 1-4 are dependant on the system hardware design, item 5 is equally important and often overlooked. Given that there is a legal maximum power output which can be transmitted, and a limit on the sensitivity of the receiver (usually constrained by cost), and that the antenna can never achieve 0dB loss (100% efficiency), then the data type is an important aspect of the design. The RF600E/D chipset use a fully balanced Manchester encoded data protocol designed for optimum use of the radio transmission path. The data format automatically includes a pre-amble, synchronisation header, followed by the encrypted and fixed code data then a CRC check. The actual packet size is 67 bits. Each transmission is followed by a guard period before another transmission can begin. The data encryption provides up to four billion changing code combinations and includes the function bits (based on which buttons were activated) along with other data and synchronization information that the decoder uses. Manchester encoding the data enables the superhetrodyne receiver data slicer to maintain efficiency for the duration of the data packet, (unlike many other encoder/decoder systems) which results in reduced bit errors and therefore ensures maximum range. Low Battery Indication The RF600E reads the battery status (voltage) on each operation. If the voltage is detected as being below 3.8 volts (typical) then a flag bit is transmitted to the decoder where it is made available. Custom Versions Custom versions of the RF600E / D chipset are available, programmed with a unique Manufacturers Key which means that the transmitter and receiver will respond only to other devices with the same unique manufacturers key. This provides a bespoke remote chipset for OEM applications. Please contact our sales department for further information. DS600-10 March 06 2004 Reg. No. 227 4001, ENGLAND Page 2