BD3570FP-E2 ROHM

Power Management IC Series for Automotive Body Control High Voltage LDO Regulators BD3570FP, BD3570HFP, BD3571FP, BD3571HFP, BD3572FP, BD3572HFP BD3573FP, BD3573HFP, BD3574FP, BD3574HFP, BD3575FP, BD3575HFP No.11036EBT02 Description BD357XFP/HFP SERIES regulators feature a high 50 V withstand-voltage and are suitable for use with onboard vehicle microcontrollers. They offer the output current of 500 mA while limiting the quiescent current to 30A (TYP).With these devices, a ceramic capacitor can be selected at the output for stable operation, the output tolerance is within 2% over the wide ambient temperature range (-40 to 125), and the short circuit protection is folded-type to minimize generation of heat during malfunction. These devices are developed to offer most robust power-supply design under the harsh automotive environment. The BD357XFP/HFP Series provide ideal solutions to lower the current consumption as well as to simplify the use with battery direct-coupled systems. Features 1) Ultra-low quiescent current: 30A (TYP.) 2) Low-saturation voltage type P-channel DMOS output transistors 3) High output voltage precision: 2%Iomax = 500 mA 4) Low-ESR ceramic capacitors can be used as output capacitors. 5) Vcc power supply voltage = 50 V 6) Built-in overcurrent protection circuit and thermal shutdown circuit 7) TO252-3, TO252-5, HRP5 Package Applications Onboard vehicle devices (body-control, car stereos, satellite navigation systems, etc.) Line up matrix BD3570FP/HFP BD3571FP/HFPBD3572FP/HFPBD3573FP/HFP BD3574FP/HFP BD3575FP/HFP Output voltage 3.3V 5.0 V Variable 3.3V 5.0 V Variable SW function Package FP:TO252-3,TO252-5 HFP:HRP5 Absolute maximum ratings (Ta=25) Parameter Symbol Limit Unit Supply voltage VCC 50 1V Switch Supply voltage VSW 50 2V Output current IO 500 mA 1.2 (TO252-3) 3 Power dissipation Pd 1.3 (TO252-5) 4 W 1.6 (HRP5) 5 Operating temperature range Topr -40 to +125 Storage temperature range Tstg -55 to +150 Maximum junction Tjmax 150 temperature 1 Not to exceed Pd and ASO. 2 for ON/OFF SW Regulator only 3 TO252-3: Reduced by 9.6 mW/ over 25 , when mounted on a glass epoxy board (70 mm 70 mm 1.6 mm). 4 TO252-5: Reduced by 10.4 mW/ over 25 , when mounted on a glass epoxy board (70 mm 70 mm 1.6 mm). 5 HRP5: Reduced by 12.8 mW/ over 25 , when mounted on a glass epoxy board (70 mm 70 mm 1.6 mm). www.rohm.com 2011.03 - Rev.B 1/9 2011 ROHM Co., Ltd. All rights reserved. BD3570FP/HFP, BD3571FP/HFP, BD3572FP/HFP, BD3573FP/HFP Technical Note BD3574FP/HFP, BD3575FP/HFP Operating Conditions Parameter SymbolMin. Max. Unit BD3570,3572,3573,3575FP/HFP VCC 4.5 6 36.0 V Input voltage BD3571,3574FP/HFP VCC 5.5 6 36.0 V Output current IO 500 mA Variable Output Voltage Range VO 2.8 12 V 6 Please consider that the Output voltage would be dropped (Dropout voltage) according to the output current. Electrical CharacteristicsUnless otherwise specified, Ta=-40 to125, VCC=13.2 V, SW=3V 7, VO settings is 5V 8 Limit Parameter Symbol Unit Conditions Min. Typ. Max. Shut Down Current lshut 10 A SW=GND Bias current lb 30 50 AIO=0mA VO VO IO=200mA, Output voltage VO VO V 0.98 1.02 VO:Please refer to Product line. ADJ Terminal voltage 8 VADJ 1.235 1.260 1.285 V IO=200mA Output current IO 0.5 A Dropout voltage Vd 0.25 0.48 V VCC=4.75V,lO=200mA 9 Ripple rejection R.R. 45 55 dB f=120Hz,ein=1Vrms,IO=100mA VCCD10VCC25V Line Regulation Reg.I 10 30 mV IO = 0 mA Load Regulation Reg.L 20 40 mV0AIO200A Swith Threshold voltage H SWH 2.0 V IO=0 mA Swith Threshold voltage L SWL 0.5 V IO=0 mA Swith Bias current SWI 22 60 ASW=5V,lO=0mA 7 BD3573,3574,3575FP/HFP only 8 BD3572,3575FP/HFP only 9 BD3571,3572,3574,3575FP/HFP only 10 BD3570,3573FP/HFP :VCCD=5.5V BD3571,3572,3574,3575FP/HFP :VCCD=6.5V This product is not designed for protection against radio active rays. www.rohm.com 2011.03 - Rev.B 2/9 2011 ROHM Co., Ltd. All rights reserved.