Datasheet Operational Amplifiers Input/Output Full Swing Low Input Offset Voltage Operational Amplifier BD5291xxx Key Specifications General Description Operating Supply Voltage (Single Supply): The BD5291xxx is ideally suited for sensor signal +1.7V to +5.5V conditioning. This features input/output full-swing Slew Rate: 2.5V/s(Typ.) operation with a supply voltage as low as 1.7V. In Operating Temperature Range: -40C to +85C addition, high common-mode rejection ratio, ultra low VSS to VDD Input Voltage Range: input bias current (1pA typical) and low input offset Input Offset Voltage: 2.5mV (Max) voltage increase the precision that can be achieved Common Mode Rejection Ratio: 70dB (Min) using these operational amplifiers. Package W(Typ) x D(Typ) x H(Max) Features SSOP5 2.90mm x 2.80mm x 1.25mm Low Operating Supply Voltage VSOF5 1.60mm x 1.60mm x 0.60mm Input Output Full Swing Low Input Offset Voltage High Common Mode Rejection Ratio High Slew Rate Applications Buffer Active Filter Sensor Amplifier Mobile Equipment Pin Configuration OUT VDD 1 5 Pin No. Pin Name 1 OUT VSS 2 2 VSS - + 3 +IN 3 4 +IN -IN 4 -IN 5 VDD BD5291FVE : VSOF5 Pin No. Pin Name +IN 1 5 VDD 1 +IN + 2 VSS 2 VSS - 3 -IN -IN 3 4 OUT 4 OUT 5 VDD Figure 1. Pin Configuration Package SSOP5 VSOF5 BD5291G BD5291FVE Product structureSilicon monolithic integrated circuit This product is not designed protection against radioactive rays. www.rohm.com TSZ02201-0RAR0G200660-1-2 2013 ROHM Co., Ltd. All rights reserved. 1/25 06.Jun.2016 Rev.005 TSZ2211114001 Datasheet BD5291xxx Ordering Information B D 5 2 9 1 x x x - T x Part Number Package Packaging and forming specification BD5291G G :SSOP5 TL: Embossed tape and reel BD5291FVE FVE :VSOF5 (SSOP5) TR: Embossed tape and reel (VSOF5) Line-up Topr Package Operable Part Number SSOP5 Reel of 3000 BD5291G-TL -40C to +85C VSOF5 Reel of 3000 BD5291FVE-TR Absolute Maximum Ratings(T =25C) A Parameter Symbol Ratings Unit Supply voltage VDD-VSS +7 V (Note 1,3) SSOP5 0.67 Power dissipation PD W (Note 2,3) VSOF5 0.25 (Note 4) Differential input voltage V VDD - VSS V ID Input common-mode V (VSS 0.3) to (VDD + 0.3 ) V ICM voltage range (Note 5) Input current I 10 mA I Operating supply voltage V +1.7 to +5.5 V opr Operating temperature T - 40 to +85 C opr Storage temperature T - 55 to +150 C stg Maximum TJmax +150 C junction temperature (Note 1) To use at temperature above T =25C reduce 5.4mW/C. A (Note 2) To use at temperature above T =25C reduce 2.0mW/C. A (Note 3) Mounted on a FR4 glass epoxy PCB 70mm70mm1.6mm (Copper foil area less than 3%). (Note 4) The voltage difference between inverting input and non-inverting input is the differential input voltage. Then input pin voltage is set to more than VSS. (Note 5) An excessive input current will flow when input voltages of more than VDD+0.6V or less than VSS-0.6V are applied. The input current can be set to less than the rated current by adding a limiting resistor. Caution: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is operated over the absolute maximum ratings. www.rohm.com TSZ02201-0RAR0G200660-1-2 2013 ROHM Co., Ltd. All rights reserved. 2/25 06.Jun.2016 Rev.005 TSZ2211115001