Datasheet 36V 2ch DC Brush Motor Driver BD60203EFV General Description Key Specifications BD60203EFV is 2ch H-bridge motor driver for DC brush Power Supply Voltage Range: 8.0 V to 28.0 V motor. This driver can facilitate low power consumption by Rated Output Current: 1.7 A PWM constant current control. Various protection circuits Rated Output Current (Peak): 3.0 A are built in. And also a circuit for lock detection is built in, Operating Temperature Range: -25 C to +85 C so it is possible to output an error detection signal Output ON-Resistance: 0.65 (Typ) corresponding to Wired-Or signaling motor lock status. It (Total of upper and lower resistors) contributes to high reliability of the set. Features Package W(Typ) x D(Typ)x H(Max) Single Power Supply Input (rated voltage of 36 V) HTSSOP-B24 7.80 mm x 7.60 mm x 1.00 mm Rated Output Current (peak): 1.7 A(3.0 A) Low ON-Resistance DMOS Output PH, EN Input Power Save Function PWM Constant Current Control (current limit function) Built-in Spike Noise Cancel Function (external noise filter is unnecessary) Driver for 2 DC Brush Motor Built-in Logic Input Pull-down Resistor Cross-conduction Prevention Circuit Thermal Shutdown Circuit (TSD) Figure 1. HTSSOP-B24 Over-current Protection Circuit (OCP) Under Voltage Lockout Circuit (UVLO) Typical Application Circuit Over Voltage Lockout Circuit (OVLO) Built-in Comparator for Lock Detection GND PH1 Ghost Supply Prevention (protects against malfunction EN1 when power supply is disconnected) PH2 LOCK1 Microminiature, Ultra-thin and High Heat-radiation EN2 (exposed metal type) HTSSOP-B24 Package LOCK2 SET1 VCC1 Applications SET2 OUT1A Plain Paper Copier (PPC), Multi-function Printer, Laser VREF1 Printer, Inkjet Printer, Photo Printer, FAX, Mini Printer and OUT1B VREF2 etc. RNF1 CR VCC2 OUT2A OUT2B TEST RNF2 PS GND Figure 2. Application Circuit Product structuresilicon monolithic integrated circuit This product has no designed protection against radioactive rays. w ww.rohm.com TSZ02201-0P2P0C301980-1-2 2018 ROHM Co., Ltd. All rights reserved. 1/19 TSZ22111 14 001 27.May.2020 Rev.002 BD60203EFV Pin Configuration Block Diagram TOP VIEW 11 LOCK1 OUT2B GND 1 24 16 SET1 Detect SET2 17 RNF2 OUT1B 2 23 12 LOCK2 VREF1 14 RNF1 1/8 3 22 NC RNF1 VREF2 15 OUT1A 1/8 4 21 OUT2A Regulator RNF2 TSD OCP VCC1 5 20 VCC2 Blank time TEST 6 PWM control UVLO OVLO 6 19 GND TEST CR 18 OSC VCC1 5 PH1 7 18 CR 4 OUT1A Forward 2 OUT1B SET2 17 EN1 8 PH1 7 Reverse 3 RNF1 8 BRAKE EN1 Open 9 16 SET1 PH2 1 GND 13 PS 20 VCC2 EN2 15 VREF2 10 Forward 9 21 PH2 Reverse OUT2A EXP-PAD 10 2 4 EN2 BRAKE OUT2B 11 14 LOCK1 VREF1 Open 23 RNF2 19 GND LOCK2 12 13 PS Figure 3. Pin Configuration Figure 4. Block Diagram Pin Descriptions Pin No. Pin Name Function Pin No. Pin Name Function 1 GND Ground pin 13 PS Power save pin 2 OUT1B H bridge output pin 14 VREF1 Current limit value setting pin Connection pin of resistor 3 RNF1 15 VREF2 Current limit value setting pin for output current detection 4 OUT1A H bridge output pin 16 SET1 Motor lock current setting pin 5 VCC1 Power supply pin 17 SET2 Motor lock current setting pin 6 TEST Test pin (Connected to GND) 18 CR Chopping frequency setting pin 7 PH1 H bridge control pin 19 GND Ground pin 8 EN1 H bridge control pin 20 VCC2 Power supply pin 9 PH2 H bridge control pin 21 OUT2A H bridge output pin 10 EN2 H bridge control pin 22 NC No connection Connection pin of resistor 11 LOCK1 Motor lock detection signal output pin 23 RNF2 for output current detection 12 LOCK2 Motor lock detection signal output pin 24 OUT2B H bridge output pin The EXP-PAD of the center of product - EXP-PAD - - - connected to GND. www.rohm.com TSZ02201-0P2P0C301980-1-2 2018 ROHM Co., Ltd. All rights reserved. 2/19 TSZ22111 15 001 27.May.2020 Rev.002 Control logic Predriver