BH76106HFV-TR ROHM

Compact Video Driver Series for DSCs and Portable Devices Compact, Low Current Consumption Single Output Video Drivers No. 15064EBT03 BH76106HFV, BH76109HFV, BH76112HFV, BH76206HFV Description This video amplifier with built-in LPF uses a full output swing type output stage to make low voltage operation at Vcc = 2.6V possible. In addition to advantages such as a tiny package and low power consumption, bands of the built-in LPF provide for 4.5 MHz products for DSC and other portable equipment and 6 MHz products for equipment such as DVD. Moreover, since it also can be used at Vcc = 5 V, it is suited not only to portable equipment but also to equipment for stationary use. Features 1) Wide operating voltage range: Vcc = 2.6 V~5.5 V th 2) Built-in 8 order LPF 3) Built-in sync-tip clamp circuit 4) Compact HVSOF6 package (3.0 mm 1.6 mm 0.75 mm) 5) Built-in standby function Standby current: 0 A (typ.) 6) Selectable gain 6dB (BH76106HFV, BH76206HFV), 9dB (BH76109HFV), 12dB (BH76112HFV) 7) Selectable filter characteristics f = 4.5 MHz (BH761xxHFV), f = 6.0 MHz (BH76206HFV) Applications Mobile phone, DSC, DVC, DVD, and other Line up matrix Product Name Amplifier Gain (dB) LPF Frequency (MHz) BH76106HFV 6 4.5 BH76109HFV 9 4.5 BH76112HFV 12 4.5 BH76206HFV 6 6.0 Absolute Maximum Ratings Parameter Symbol Rating Unit Power Supply Voltage Vcc 7 V Power Dissipation Pd 410 mW Operating Temperature Topr -40+85 Range Storage Temperature Tstg -55+125 Range When mounted on a 70 mm70 mm1.6 mm ROHM standard board, reduce by 4.1mW/ above Ta=+25 Operating Range Parameter Symbol Min. Typ. Max. Unit Power Supply Voltage Vcc 2.6 3.0 5.5 V This product is not designed for protection against radio active rays. www.rohm.com 2015.07 Rev.B 1/8 2015 ROHM Co., Ltd. All rights reserved. Technical Note BH76106HFV, BH76109HFV, BH76112HFV, BH76206HFV Electrical Characteristics (Unless otherwise noted, Typ.: Ta = 25 C, VCC = 3.0 V) Typical Values Parameter Symbol Unit Measurement Conditions BH76106 BH76109 BH76112 BH76206 HFV HFV HFV HFV Circuit Current 1 Icc1 7 8 mA With no signal Circuit Current 2 Icc2 0.0 A In standby Voltage Gain Gv 6.0 9.0 12.0 6.0 dBf=100kHz, Vin =1Vpp f=4.5MHz/100kHz(BH761xxHFV) Maximum Output Level Vomv 2.6 Vpp f=6MHz/100kHz(BH76206HFV) f=4.5MHz/100kHz(BH761xxHFV) Frequency Characteristic 1 Gf1 0.1 -0.3 dB f=6MHz/100kHz(BH76206HFV) f=8.2MHz/100kHz(BH761xxHFV) Frequency Characteristic 2 Gf2 -4.0 dB f=12MHz/100kHz(BH76206HFV) f=19MHz/100kHz(BH761xxHFV) Frequency Characteristic 3 Gf3 -45.0 -40.0 dB f=27MHz/100kHz(BH76206HFV) 100kHz500kHz band Y Channel output S/N SNY -67.0 dB 75 termination 100 white video signal 100kHz500kHz band C Channel output S/N (AM) SNCA -77.0 dB 75 termination 100 chroma video signal 100kHz500kHz band C Channel output S/N (PM) SNCP -65.0 dB 75 termination 100 chroma video signal VIN = 1.0 Vp-p Differential Gain DG 0.7 0.8 % Standard stair-step signal VIN = 1.0 Vp-p Differential Phase DP 0.7 0.8 deg Standard stair-step signal Standby Switching Voltage VthH 1.2Vcc V Standby OFF High Level Standby Switching Voltage VthL 00.45 V Standby ON Low Level Standby Switch Input Current IthH 45 66 A Applying 3.0 V to Pin 6 High Level Control pin settings Parameter State Function H Active Standby (Pin 6) L Standby OPEN Standby Block Diagram 6 1 STBY GND Sync Tip Clamp Vin Vsag 5 2 BH76106HFV :6dB 3 75 AMP 4 BH76109HFV :9dB 8th order Vout VCC LPF BH76112HFV :12dB BH76206HFV :6dB Fig.1 Pin Descriptions (Typical voltage is that when Vcc = 3.0 V, Ta = 25 C) Pin Pin Typical IN OUT Equivalent Circuit Function No. Name voltage VCC 4 Vcc - - 3.0V Power supply pin www.rohm.com 2015.07 Rev.B 2/8 2015 ROHM Co., Ltd. All rights reserved.