Datasheet AC/DC Drivers PWM Control IC BM1P066FJ General Features The PWM control IC for AC/DC BM1P066FJ PWM frequency: 65 kHz provides an optimum system for all products that PWM current mode method include an electrical outlet. Frequency hopping function A built-in start circuit that withstands 650 V helps to Burst operation during light load / Frequency keep power consumption low. Both isolated and reduction function non-isolated versions are supported, making for 650 V start circuit simpler design of various types of low-power VCC pin undervoltage protection converters. Switching MOSFET and current detection VCC pin overvoltage protection resistors are external devices, thus achieving a higher CS pin open protection degree of freedom in power supply design. The CS pin Leading-Edge-Blanking function switching frequency is set as fixed. Since current mode Per-cycle overcurrent limiter function control is used, a current limit is imposed in each cycle, Overcurrent limiter with AC voltage compensation and excellent performance is demonstrated in function bandwidth and transient response. With a light load, Soft start function frequency is reduced and higher efficiency is realized. Secondary overcurrent protection circuit A frequency hopping function is also built in, contributing to low EMI. Also on chip are soft start and burst functions, a Package per-cycle overcurrent limiter, VCC overvoltage SOP-J8 4.90 mm 6.00 mm 1.65 mm pitch 1.27 mm protection, overload protection, and other protection (Typ.) (Typ.) (Typ.) (Typ.) functions. Basic Specifications Operating power supply voltage range: VCC 8.9 V to 26.0 V VH: to 600 V Applications Operating current: Normal: 0.60 mA (Typ.) AC adapters, TV s, and household appliances Burst mode: 0.35 mA (Typ.) (vacuum cleaners, humidifiers, air cleaners, air Oscillation frequency: BM1P066FJ: 65 kHz (Typ.) conditioners, IH cooking heaters, rice cookers, etc.) Operating temperature range: -40C to +85C Application circuit Line-up X-cap Frequency VCCOVP VCC recharge Brown-out discharge BM1P061FJ 65kHz Auto-restart BM1P062FJ 65kHz Latch BM1P063FJ 65kHz Auto-restart BM1P064FJ 65kHz Latch BM1P065FJ 65kHz Auto-restart BM1P066FJ 65kHz Latch BM1P067FJ 65kHz Auto-restart BM1P068FJ 65kHz Latch BM1P101FJ 100kHz Auto-restart BM1P102FJ 100kHz Latch BM1P103FJ 100kHz Auto-restart BM1P104FJ 100kHz Latch BM1P105FJ 100kHz Auto-restart BM1P106FJ 100kHz Latch BM1P107FJ 100kHz Auto-restart BM1P108FJ 100kHz Latch Figure 1Application Circuit Product structureSilicon monolithic integrated circuit This product is not designed for protection against radioactive rays . www.rohm.com TSZ02201-0F2F0A200200-1-2 2013 ROHM Co., Ltd. All rights reserved. 1/27 30.Oct.2013.Rev.001 TSZ2211114001 DatasheetDatasheet BM1P066FJ Absolute Maximum Ratings (Ta = 25C) Parameter Symbol Rating Unit Conditions Maximum voltage 1 Vmax1 -0.3 ~ 30.0 V VCC Maximum voltage 2 Vmax2 -0.3 ~ 6.5 V CS, FB, ACMONI Maximum voltage 3 Vmax3 -0.3 ~ 15.0 V OUT Maximum voltage 4 Vmax4 -0.3 ~ 650 V VH OUT pin peak current I 1.0 A OUT Allowable dissipation Pd 674.9 (Note1) mW When mounted o Operating temperature range Topr -40 ~ +85 C o Storage temperature range Tstr -55 ~ +150 C (Note1) SOP-J8: When mounted, 70 70 1.6 mm (glass epoxy on single-layer substrate). Reduce to 5.40 mW/C when used at Ta = 25C or above. Recommended Operating Conditions (Ta = 25C) Parameter Symbol Rating Unit Conditions Supply voltage range 1 VCC 8.9 ~ 26.0 V VCC pin voltage Supply voltage range 2 VH 80 ~ 600 V VH pin voltage Electrical Characteristics (Unless otherwise noted, Ta = 25C, VCC = 15 V) Rating Parameter Symbol Unit Conditions Min. Typ. Max. Circuit current FB = 2.0 V Circuit current (ON) 1 ION1 - 600 1000 A (during pulse operation) FB = 0.0 V Circuit current (ON) 2 ION2 - 350 450 A (during burst operation) VCC pin (5 pin) protection function VCC UVLO voltage 1 VUVLO1 12.50 13.50 14.50 V VCC rise VCC UVLO voltage 2 VUVLO2 7.50 8.20 8.90 V VCC drop VCC UVLO hysteresis VUVLO3 - 5.30 - V VUVLO3 = VUVLO1-VUVLO2 VCC OVP voltage 1 VOVP1 26.00 27.50 29.00 V VCC rise VUVLO2- VCC LATCH released voltage VLATCH - - V 0.5 Output driver block OUT pin H voltage VOUTH 10.5 12.5 14.5 V IO = -20 mA OUT pin L voltage VOUTL - - 1.00 V IO = +20 mA OUT pin pull-down resistance RPDOUT 75 100 125 k ACMONI detection circuit ACMONI detection voltage1 VACMON1 0.92 1.00 1.08 V ACMONI rises ACMONI detection voltage2 VACMON2 0.63 0.70 0.77 V ACMONI falls ACMONI Hysteresis VACMON3 0.20 0.30 0.40 V ACMONI Timer TACMON1 180 256 330 ms Start circuit block Start current 1 ISTART1 0.400 0.700 1.000 mA VCC = 0 V Start current 2 ISTART2 1.000 3.000 5.000 mA VCC = 10 V Inflow current from VH pin OFF current ISTART3 - 10 20 uA after release of UVLO Start current switching voltage VSC 0.400 0.800 1.400 V www.rohm.com TSZ02201-0F2F0A200200-1-2 2013 ROHM Co., Ltd. All rights reserved. 2/27 30.Oct.2013.Rev.001 TSZ2211115001