Technical Data Sheet Calibration Kit RPC-2.92 02S30R-MSOS3 Plug All dimensions are in mm tolerances according to ISO 2768 m-H Interface According to IEC 61169-35 Mechanically compatible with RPC-3.50 and SMA Contents and Documentation This kit is delivered with Standard Definitions Card Printed Standard Definitions that can be used on nearly all Vector Network Analyzers Test Results Documentation Hard Shell Case Protection Caps Material and plating Connector parts Material Plating Center conductor CuBe Gold, min. 1.27 m, over nickel Outer conductor Stainless steel Passivated Coupling nut Stainless steel Passivated Body Aluminum black anodized Dielectric PS Substrate Al O 2 3 Rosenberger Hochfrequenztechnik GmbH & Co. KG Page Tel. : +49 8684 18-0 P.O.Box 1260 D-84526 Tittmoning Germany Email : info rosenberger.de www.rosenberger.de 1 / 3 RF 35/09.14/6.2 Dieses Dokument ist urheberrechtlich geschtzt This document is protected by copyright Rosenberger Hochfrequenztechnik GmbH & Co. KG Technical Data Sheet Calibration Kit RPC-2.92 02S30R-MSOS3 Plug Electrical data Frequency range DC to 40.0 GHz Open 1 Error from nominal phase 1.5, DC to 4 GHz 4.0, 4 GHz to 26.5 GHz 5.0, 26.5 GHz to 40.0 GHz Short 2 Error from nominal phase 1.5, DC to 4 GHz 4.0, 4 GHz to 26.5 GHz 5.0, 26.5 GHz to 40.0 GHz Load Return loss 40.0 dB, DC to 4 GHz 28.0 dB, 4 GHz to 26.5 GHz 25.0 dB, 26.5 GHz to 40.0 GHz DC Resistance 50 0.5 Power handling (at 25 C, sea level) 0.5 W, derate by 0.005 W/K 1 The nominal phase is defined by the Offset Delay, the Offset Loss and the Fringing Capacitances 2 The nominal phase is defined by the Offset Delay, the Offset Loss and the Short Inductance Mechanical data Mating cycles 500 Maximum torque 1.70 Nm Recommended torque 0.90 Nm Gauge 0.00 mm to 0.08 mm General standard definitions For proper operation the vector network analyzer (VNA) needs a model describing the electrical behaviour of this calibration standard. The different models, units, and terms used will depend on the VNA type and they will have to be entered into the VNA. All values are based on typical geometry and plating. Open Offset Z / Impedance / Z 50 o o Offset Delay 28.353 ps Length (electrical) / Offset Length 8.50 mm Offset Loss 2.40 G/s Loss 0.0118 dB/ GHz -15 Fringing Capacitances C = -7.38000 x 10 F / -7.38000 fF 0 -27 C = 1180.00 x 10 F/Hz / 1.18000 fF /GHz 1 -36 2 2 C = -44.8000 x 10 F/Hz / -0.04480 fF /GHz 2 -45 3 3 C = 0.54000 x 10 F/Hz / 0.00054 fF /GHz 3 Rosenberger Hochfrequenztechnik GmbH & Co. KG Page Tel. : +49 8684 18-0 P.O.Box 1260 D-84526 Tittmoning Germany Email : info rosenberger.de www.rosenberger.de 2 / 3 RF 35/09.14/6.2 Dieses Dokument ist urheberrechtlich geschtzt This document is protected by copyright Rosenberger Hochfrequenztechnik GmbH & Co. KG