Technical Data Sheet Calibration Kit RPC-3.50 03K30R-MSOTS3 Jack All dimensions are in mm tolerances according to ISO 2768 m-H Interface According to IEC 61169-23 Mechanically compatible with RPC-2.92 and SMA Contents and Documentation This kit is delivered with Standard Definitions Card Printed Standard Definitions that can be used on nearly all Vector Network Analyzers Test Results Documentation Hard Shell Case Protection Caps Material and plating Connector parts Material Plating Center conductor CuBe Gold, min. 1.27 m, over nickel Outer conductor Stainless steel Passivated Body Aluminum black anodized Dielectric PS Substrate Al O 2 3 Rosenberger Hochfrequenztechnik GmbH & Co. KG Page Tel. : +49 8684 18-0 P.O.Box 1260 D-84526 Tittmoning Germany Email : info rosenberger.de www.rosenberger.de 1 / 3 RF 35/09.14/6.2 Dieses Dokument ist urheberrechtlich geschtzt This document is protected by copyright Rosenberger Hochfrequenztechnik GmbH & Co. KG Technical Data Sheet Calibration Kit RPC-3.50 03K30R-MSOTS3 Jack Electrical data Fr Frequency range DC to 26.5 GHz Thru Return loss 34 dB, DC to 4 GHz 32 dB, 4 GHz to 8 GHz 30 dB, 8 GHz to 26.5 GHz Open 1 Error from nominal phase 1.0, DC to 4 GHz 2.0, 4 GHz to 8 GHz 3.0, 8 GHz to 26.5 GHz Short 2 Error from nominal phase 1.0, DC to 4 GHz 2.0, 4 GHz to 8 GHz 3.0, 8 GHz to 26.5 GHz Load Return loss 40.0 dB, DC to 4 GHz 35.0 dB, 4 GHz to 8 GHz 30.0 dB, 8 GHz to 26.5 GHz DC Resistance 50 0.5 Power handling (at 25 C, sea level) 0.5 W, derate by 0.005 W/K 1 The nominal phase is defined by the Offset Delay, the Offset Loss and the Fringing Capacitances 2 The nominal phase is defined by the Offset Delay, the Offset Loss and the Short Inductance Mechanical data Mating cycles 500 Maximum torque 1.70 Nm Recommended torque 0.90 Nm Gauge 0.00 mm to 0.08 mm General standard definitions For proper operation the vector network analyzer (VNA) needs a model describing the electrical behaviour of this calibration standard. The different models, units, and terms used will depend on the VNA type and they will have to be entered into the VNA. All values are based on typical geometry and plating. Thru Offset Zo / Impedance / Zo 50 Offset Delay 84.058 ps Length (electrical) / Offset Length 25.20 mm Offset Loss 2.51 G/s Loss 0.0183 dB/ GHz Line Loss 1GHz 0.0007 dB/mm Open Offset Zo / Impedance / Zo 50 Offset Delay 33.356 ps Length (electrical) / Offset Length 10.00 mm Offset Loss 2.20 G/s Loss 0.0127 dB/ GHz -15 Fringing Capacitances C0 = -17.500 x 10 F / -17.500 fF -27 C1 = -2000.0 x 10 F/Hz / -2.0000 fF /GHz -36 2 C2 = 140.00 x 10 F/Hz / 0.1400 fF /GHz -45 3 C3 = -2.7000 x 10 F/Hz / -0.0027 fF /GHz Rosenberger Hochfrequenztechnik GmbH & Co. KG Page Tel. : +49 8684 18-0 P.O.Box 1260 D-84526 Tittmoning Germany Email : info rosenberger.de www.rosenberger.de 2 / 3 RF 35/09.14/6.2 Dieses Dokument ist urheberrechtlich geschtzt This document is protected by copyright Rosenberger Hochfrequenztechnik GmbH & Co. KG