Technical Data Sheet Calibration Kit N 50 53S38R-MSON3 Plug All dimensions are in mm tolerances according to ISO 2768 m-H Interface According to IEC 61169-16 Contents and Documentation This kit is delivered with Standard Definitions Card Printed Standard Definitions that can be used on nearly all Vector Network Analyzers Test Results Documentation Lanyard Hard Shell Case Protection Caps Material and plating Connector parts Material Plating Center conductor Brass Gold, min. 1.27 m, over nickel Outer conductor Brass Flash white bronze over silver(e.g. Optargen) Coupling nut Brass White bronze(e.g. Optalloy) Body Brass powder-coated Dielectric PTFE / PPE Substrate Al2O3 Rosenberger Hochfrequenztechnik GmbH & Co. KG Page Tel. : +49 8684 18-0 P.O.Box 1260 D-84526 Tittmoning Germany Email : info rosenberger.de www.rosenberger.de 1 / 3 RF 35/09.14/6.2 Dieses Dokument ist urheberrechtlich geschtzt This document is protected by copyright Rosenberger Hochfrequenztechnik GmbH & Co. KG Technical Data Sheet Calibration Kit N 50 53S38R-MSON3 Plug Electrical data Frequency range DC to 8 GHz Open 1 Error from nominal phase 3.0, DC to 6 GHz 5.0, 6 GHz to 8 GHz Short 2 Error from nominal phase 2.0, DC to 6 GHz 4.0, 6 GHz to 8 GHz Load Return loss 42 dB, DC to 2.5 GHz 38 dB, 2.5 GHz to 6 GHz 35 dB, 6 GHz to 8 GHz DC Resistance 50 0.5 Power handling (at 25 C, sea level) 1.0 W, derate by 0.01 W/K 1 The nominal phase is defined by the Offset Delay, the Offset Loss and the Fringing Capacitances 2 The nominal phase is defined by the Offset Delay, the Offset Loss and the Short Inductance Mechanical data Mating cycles 500 Maximum torque 1.70 Nm Recommended torque 1.10 Nm Gauge 5.28 mm to 5.84 mm General standard definitions For proper operation the vector network analyzer (VNA) needs a model describing the electrical behaviour of this calibration standard. The different models, units, and terms used will depend on the VNA type and they will have to be entered into the VNA. All values are based on typical geometry and plating. Open Offset Zo / Impedance / Zo 50 Offset Delay 67.78 ps Length (electrical) / Offset Length 20.32 mm Offset Loss 0.80 G/s Loss 0.0094 dB/ GHz -15 Fringing Capacitances C0 = -11.4000 x 10 F / -11.4000 fF -27 C1 = 9000.00 x 10 F/Hz / 9.00000 fF /GHz -36 2 2 C2 = -1180.00 x 10 F/Hz / -1.18000 fF /GHz -45 3 3 C3 = 20.0000 x 10 F/Hz / 0.02000 fF /GHz Rosenberger Hochfrequenztechnik GmbH & Co. KG Page Tel. : +49 8684 18-0 P.O.Box 1260 D-84526 Tittmoning Germany Email : info rosenberger.de www.rosenberger.de 2 / 3 RF 35/09.14/6.2 Dieses Dokument ist urheberrechtlich geschtzt This document is protected by copyright Rosenberger Hochfrequenztechnik GmbH & Co. KG