Automotive Low Resistance Thick Film Chip resistor -CS Feature Figures L Ultra-low Value A 1. High purity Alumina substrate 2. Protective coating Low Temperature Coefficient 3. Resistance element W H Suitable for reflow & wave soldering B 4. Termination (Inner) Ni / Cr L Application: Power supply 5. Termination (Between) Ni Barrier 6. Termination (Outer) Sn Derating Curve & Specification Type Dielectirc Withstanding Voltage Operating Temperature CS02 100V -55C~155C CS03 300V -55C~155C CS05 500V -55C~155C CS06 500V -55C~155C CS07 500V -55C~155C Ambient temperature (C) CS10 500V -55C~155C CS11 500V -55C~155C CS12 500V -55C~155C Power Rating Resistance Range Type Size L(mm) W(mm) H(mm) A(mm) B(mm) T.C.R. 70C 1% & 5% 0402 50mR<100m: 700 ppm/C CS02 1/8W 1.000.10 0.500.05 0.350.05 0.200.10 0.250.10 50m~1 (1005) 100mR1: 200 ppm/C 10mR<15m: 1500ppm/C 15m R<20m: 1000ppm/C 20mR<30m: 800 ppm/C 0603 CS03 1/5W 1.600.10 0.800.10 0.450.10 0.300.20 0.300.20 10m~1 30mR<33m: 600 ppm/C (1608) 33mR50m: 400 ppm/C 50m<R0.1: 300 ppm/C 0.1<R1: 200 ppm/C 10mR15m: 800 ppm/C 15m<R25m: 600 ppm/C 0805 +0.15 CS05 1/4W 2.000.15 1.25 0.550.10 0.400.20 0.400.20 10m~1 25m<R50m: 400 ppm/C (2012) - 0.10 50m<R0.2: 200 ppm/C 0.2<R1: 100 ppm/C 10mR<15m: 700ppm/C 15mR30m: 400ppm/C 1206 +0.15 CS06 1/3W 3.100.15 1.55 0.550.10 0.450.20 0.450.20 10m~1 30m<R50m: 300ppm/C (3216) - 0.10 50m<R0.1: 200ppm/C 0.1<R1: 150ppm/C 10mR<15m: 500ppm/C 1210 15mR<20m: 400ppm/C CS07 1/2W 3.100.10 2.600.20 0.550.10 0.500.25 0.500.20 10m~1 (3225) 20mR50m: 300ppm/C 50m<R1: 100ppm/C 10mR<15m: 600ppm/C 15mR<20m: 500ppm/C 2010 20mR30m: 300ppm/C CS10 3/4W 5.000.10 2.500.20 0.550.10 0.600.25 0.500.20 10m~1 (5025) 30m<R50m: 200ppm/C 50m<R0.1: 150ppm/C 0.1<R1: 100ppm/C 10mR<20m: 500ppm/C 1812 20mR<50m: 400ppm/C CS11 3/4W 4.500.20 3.200.20 0.550.20 0.500.20 0.800.30 10m~1 (4532) 50mR0.1: 200ppm/C 0.1<R1: 100ppm/C 10mR<15m: 600ppm/C 15mR<20m: 400ppm/C 2512 20mR30m: 300ppm/C CS12 1W 6.350.10 3.200.20 0.550.10 0.600.25 0.800.30 10m~1 (6432) 30m<R50m: 200ppm/C 50m<R0.1: 150ppm/C 0.1<R1: 100ppm/C 44 Percent rated load (%) W HAutomotive Low Resistance Thick Film Chip resistor -CS Performance Specifications Test Item Reference standard Test Methods Evaluation Criteria Pre- and Post-Stress AEC-Q200 TEST 1 2.5x Rated voltage or Max. Overload Voltage whichever is lower for 5 seconds, then 1%: (1.0%+0.05) ElectricalTest IEC60115 4.13 check the resistance. 5%: (2.0%+0.05) (Short time Overload) Biased Humidity AEC-Q200 TEST 7 1000 hours 85C/85%RH. Note: Specified conditions:10% of operating power. 1%: (1.0%+0.05) MIL-STD-202 Method 103 Measurement at 244 hours after test conclusion. 5%: (3.0%+0.05) Operational Life AEC-Q200 TEST 8 1,000 hours at 125C, applied de-rated (36%) power of continuous working 1%: (1.0%+0.1) MIL-STD-202 Method 108 5%: (3.0%+0.1) voltage, 1.5 hours on, 0.5 hour off. Resistance to AEC-Q200 TEST 15 Condition B No pre-heat of samples. Note: Single Wave Solder - Procedure 2 for SMD (1.0%+0.05) Soldering Heat MIL-STD-202 Method 210 and Procedure 1 for Leaded with solder within 1.5mm of device body. Solderability AEC-Q200 TEST 18 SMD. Electrical test not required. Magnification 50 X. Coverage must be over 95%. J-STD-002 Conditions: 1. Baking 4 hours 155C dry heat, dipping 2453C for 50.5 second. 2. Steam aging 8 hours, dipping 2603C for 300.5 second. Board Flex AEC-Q200 TEST 21 Bending 3mm(CS02-CS05)/2mm(CS06-CS12)for 605sec (1.0%+0.05 AEC-Q200-005 * CS07 size in 0.75W 0.1~1 100PPM/C could be provided specially Ordering Procedure (Example: CS12 1W 5% 22m T/R-4000) CS121W J 0 2 2 L T4E Product Type: Wattage: Resistance Value: Packing Qty.: Fill-in 4 digits with the Chip Fill-in 2 digits with the codes as follow: 5% (E-24 series): 4=4,000pcs, st nd rd resistor type as follow: WA=1/10W W8=1/8W W4=1/4W the 1 digit is 0, the 2 & 3 digits are for 5=5,000pcs CS02, CS03, CS05, CS06, W5=1/5W W3=1/3W W2=1/2W the significant figures of the resistance C=10,000pcs th CS07, CS10, CS11, CS12 07 = 3/4W 1W=1W and the 4 indicate the numbers of zeros D=20,000pcs following Special Feature : 1%( E-24, E-96 series): st rd E = Lead Free (standard) Tolerance: the 1 to 3 digits are for the significant th F = 1% figures of the resistance and the 4 J = 5% indicate the numbers of zeros following. Packing Type: T = T/R B = Bulk in Poly bag C = Bulk in cassette Remark: For more details, please check page 135, Part No. System 45