HLE-10302GDVBETR Samtec

REVISION AQ HLE-1XX-02-XXX-DV-XX-XX-XX OPTION DO NOT -TR: TAPE & REEL No OF POSITIONS SCALE FROM (2 - 29 POSITIONS ONLY) -02 THRU -50 THIS PRINT FIG 5 (PER ROW) OPTION -BE OPTION -P: PICK & PLACE PAD RHLE-50-DBE LEAD STYLE (SAME AS FIG 1 UNLESS OTHERWISE STATED) (POS -03 THRU -50 ONLY) -02: SURFACE MOUNT -A: ALIGNMENT PIN (4 POS MIN) (USE C-132-12-X) -LC: LOCKING CLIP (2 POS MIN) (SEE NOTE 9) C PLATING SPECIFICATION -K: USE K-DOT-.256-.375-.005 +.008 [.20] No OF POS x .100 [2.54] POLYAMIDE FILM PAD (AVAILABLE -G: 20" GOLD IN CONTACT AREA -.005 [.13] ON POS -03 THRU -50; .005 [.13] 3" ON TAIL (USE C-132-12-G) THICKNESS) -S: 30" SELECTIVE GOLD IN CONTACT AREA MATTE TIN ON TAIL (SEE FIG 4) (USE C-132-12-S) ({No of POS - 1} x .100 [2.54]) -F: 3" SELECTIVE FLASH GOLD IN CONTACT .005 [.13] AREA MATTE TIN ON TAIL OPTION .100 2.54 (USE C-132-12-F) -BE: BOTTOM ENTRY REF 02 -L: 10" SELECTIVE LIGHT GOLD IN (USE RHLE-50-DBE)(SEE FIG. 5) CONTACT AREA MATTE TIN ON TAIL (LEAVE BLANK FOR STANDARD) (USE C-132-12-L) .200 5.08 -H: 30" HEAVY GOLD IN CONTACT AREA REF 3" ON TAIL (USE C-132-12-H) -STL: 30" SELECTIVE GOLD IN CONTACT 01 AREA TIN/LEAD (90%/10 +/-5%) ROW SPECIFICATION (USE C-132-12-STL) -SM: 30" SELECTIVE GOLD IN CONTACT -DV: DOUBLE VERTICAL AREA MATTE TIN ON TAIL C-132-12-XXX (USE RHLE-50-D) 2 MAX SWAY (USE C-132-12-S) -FM: 3" SELECTIVE FLASH GOLD IN CONTACT (EITHER DIRECTION) AREA MATTE TIN ON TAIL (USE C-132-12-F) .020 0.51 REF -LM: 10" LIGHT GOLD IN CONTACT AREA MATTE TIN ON TAIL (USE C-132-12-L) PATENT NUMBERS 5713755 / 5961339 RHLE-50-D .259 6.58 REF SEE NOTE 10 903 C C .144 3.66 SEE TABLE 2 SECTION NOTES: C FIG 1 1. REPRESENTS A CRITICAL DIMENSION. 2. ALL IDENTIFICATION MARKS MUST NOT STAND GREATER THAN .002 [.05] OFF THE SURFACE OF THE PART. HLE-116-02-XXX-DV SHOWN 3. PULL OUT FORCE FOR -LC, -A, & CONTACT IS 12 oz MIN. 4. COPLANARITY: SEE TABLE 2. 5. BURR ALLOWANCE: .003 [.08] MAX 6. CUT ASSEMBLIES AFTER FILL. CUT FLASH TO BE .010 MAX WITH NO FLASH ALLOWED IN HOLES OR EXTENDING BELOW LEADS. WILL LOSE A POSITION FIG 2 FOR EVERY CUT MADE ON A SOCKET STRIP. -A & -LC OPTION 7. TUBE POSITIONS 03 THRU 50. LAYER PACKAGE POSITION 02. 8. ENDWALL THICKNESS: .030+/-.005[.76+/-.13] TO BE MEASURED FROM BOTTOM VIEW. .050 1.27 9. DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED, THE LC OPTION IS NOT COMPATIBLE WITH AUTO PLACEMENT. SAMTEC RECOMMENDS MANUAL PLACEMENT (No OF POS -2) x.1000 [2.540] C FOR ALL ASSEMBLIES WITH THE LC OPTION. 10. SAMTEC LOGO MAY NOT BE PRESENT ON CUT TO POSITION CONNECTORS. C .050 1.27 PROPRIETARY NOTE UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES. THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO TOLERANCES ARE: SAMTEC, INC. AND SHALL NOT BE REPRODUCED DECIMALS ANGLES OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY .XX: .01 [.3] 3 520 PARK EAST BLVD, NEW ALBANY, IN 47150 SM-A10H PURPOSE OTHER THAN THAT WHICH IT WAS .XXX: .005 [.13] PHONE: 812-944-6733 FAX: 812-948-5047 OBTAINED WITHOUT THE EXPRESSED WRITTEN .008 x .056 REF LC-08-TM-01 .XXXX: .0020 [.051] e-Mail: info@SAMTEC.com code: 55322 .0625 1.588 CONSENT OF SAMTEC, INC. [.20 x 1.42] MATERIAL: DO NOT SCALE DRAWING SHEET SCALE: 2:1 DESCRIPTION: [2.54] .100 TIGER BEAM SOCKET ASSEMBLY 3 MAX SWAY BODY: VECTRA E130i DWG. NO. (EITHER DIRECTION) 3 MAX SWAY CONTACT: BeCu (EITHER DIRECTION) HLE-1XX-02-XXX-DV-XX-XX-XX F:\DWG\MISC\MKTG\HLE-1XX-02-XXX-DV-XX-XX-XX-MKT.SLDDRW SHEET OF BY: ED MESSER 12/19/98 1 2REVISION AQ NOTE: = USE MEASURED DIM (REF) FIG 3 = { - .225 [5.72])/2} .020 [.51] (-P: PICK AND PLACE PAD) AVAILABLE ON POSITIONS 03 THRU 50 C .280 7.11 C .152 3.86 LMP-02 .225 5.72 FIG 4 -K: POLYMIDE FILM PAD AVAILABLE ON POS 03 THRU 50 (SEE NOTE) C (SEE NOTE) .028.010 [.71 .25] .149 3.78 C NOTE: = USE MEASURED DIM (REF) = { - .2559 [6.500])/2} .020 [.51] F:\DWG\MISC\MKTG\HLE-1XX-02-XXX-DV-XX-XX-XX-MKT.SLDDRW PROPRIETARY NOTE THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PURPOSE OTHER THAN THAT WHICH IT WAS PHONE: 812-944-6733 FAX: 812-948-5047 OBTAINED WITHOUT THE EXPRESSED WRITTEN e-Mail: info@SAMTEC.com code: 55322 CONSENT OF SAMTEC, INC. DESCRIPTION: DO NOT SCALE DRAWING .100 TIGER BEAM SOCKET ASSEMBLY DWG. NO. PT-1-24-10-63 SHEET SCALE: 2:1 HLE-1XX-02-XXX-DV-XX-XX-XX PT-1-24-01-64 TUBE VIEWS SHEET OF BY: ED MESSER 12/19/98 2 2