HLE-108-02-G-DV-PE-LC Samtec

REVISION X HLE-1XX-02-XX-DV-XE-XX DO NOT No OF POSITIONS OPTION SCALE FROM -02 THRU -50 -BE: BOTTOM ENTRY THIS PRINT (PER ROW) (USE RHLE-50-DBE) (SEE FIG. 3) LEAD STYLE (AVAILABLE ON -PE X -02 STYLE ONLY) -LC: LOCKING CLIP (SEE NOTE 10) (USE LC-08-TM-01) PLATING SPECIFICATION (AVAILABLE ON -PE -G: GOLD STYLE ONLY) (SEE TABLE 1) -TR: TAPE & REEL C1 +.008 -L: LIGHT SELECTIVE GOLD, (2 - 29 POSITIONS ONLY) No OF POS. x .100 -.005 MATTE TIN TAIL (-TE & -PE OPTIONS ONLY) (SEE TABLE 1) -P: METAL PAD (No OF POS. -1) x .100 -S: SELECTIVE GOLD, (USE MPP-02) MATTE TIN TAIL (SEE FIG. 2) 02 (SEE TABLE 1) ENTRY STYLE -LM: LIGHT SELECTIVE GOLD, -PE: PASS THROUGH ENTRY MATTE TIN TAIL (SEE TABLE 1) .200 (SEE FIG. 1) .100 REF -SM: SELECTIVE GOLD, MATTE TIN -TE: TOP ENTRY REF TAIL (SEE TABLE 1) (SEE FIG. 2) -F: FLASH SELECTIVE GOLD, MATTE TIN TAIL (SEE TABLE 1) 01 ROW SPECIFICATION -DV: DOUBLE VERTICAL (USE RHLE-50-DXX) .138 .050 (TYP) REF .008 REF .020 REF (SEE SECTION, SHT 2 FOR DIMENSIONS) 2 MAX SWAY 2 MAX SWAY (TYP) (TYP) ( (No. OF POS - 2) x .100 .005 FIGURE 1 (-PE: PASS THROUGH ENTRY) NOTES: (SHOWN WITH -LC OPTION) C 1. REPRESENTS A CRITICAL DIMENSION. 2. CUT ASSEMBLIES AFTER FILL. CUT FLASH TO BE .010 MAX WITH NO FLASH ALLOWED IN HOLES OR EXTENDING BELOW LEADS. WILL LOSE A POSITION UNLESS OTHERWISE SPECIFIED, PROPRIETARY NOTE FOR EVERY CUT. DIMENSIONS ARE IN INCHES. THIS DOCUMENT CONTAINS INFORMATION 3. TUBE POSITIONS 03 THRU 50. LAYER PACKAGE POSITION 02. CONFIDENTIAL AND PROPRIETARY TO TOLERANCES ARE: SAMTEC, INC. AND SHALL NOT BE REPRODUCED 4. ENDWALL THICKNESS: .030 .003. DECIMALS ANGLES OR TRANSFERRED TO OTHER DOCUMENTS OR 5. MINIMUM CONTACT RETENTION IN PLASTIC: 12 OUNCES DISCLOSED TO OTHERS OR USED FOR ANY .XX: .01 2 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PURPOSE OTHER THAN THAT WHICH IT WAS 6. AFTER PLATING, PIN IS NAMED SUB-C-132-10-X. AFTER FORMING, PIN IS C-132-10-X .XXX: .005 PHONE: 812-944-6733 FAX: 812-948-5047 OBTAINED WITHOUT THE EXPRESSED WRITTEN .XXXX: .0020 7. MAX VARIATION OF 3 DEGREES WITHIN 16 PINS. CONSENT OF SAMTEC, INC. e-Mail: info SAMTEC.com code: 55322 8. MEASURE FROM BEND TO TIP OF PIN. DO NOT SCALE DRAWING SHEET SCALE: 2:1 DESCRIPTION: MATERIAL: 9. MEASURE FROM CONTACT BARB AREA TO TIP OF PIN .100 C.L. SINGLE BEAM SOCKET STRIP BODY: VECTRA E130i 10. DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED, THE X COLOR: BLACK DWG. NO. -LC OPTION IS NOT COMPATIBLE WITH AUTO PLACEMENT, SAMTEC HLE-1XX-02-XX-DV-XE-XX RECOMMENDS MANUAL PLACEMENT FOR ALL ASSEMBLIES WITH CONTACT: BeCu THE -LC OPTION. BY: KEVIN B 10/27/99 SHEET OF1 2 F: DWG MISC MKTG HLE-1XX-02-XX-DV-XE-XX-MKT.SLDDRWREVISION X/2 -.1125.010 .280 REF .225 REF SEE TABLE 1 FIGURE 3 .146 (BOTTOM ENTRY OPTION) C5 .120 .100 C6 +4 90 -2 FIGURE 2 (-TE WITH -P OPTION) SEE TABLE 1 +.010 MEASURE OVER BEND 903 C4 C2 .144 (TYP.) -.000 CLOSEST TO THE BODY .090 .056 REF (TYP.) .006 REF +.015 .300 -.010 C3 PACKAGING VIEWS SECTION F: DWG MISC MKTG HLE-1XX-02-XX-DV-XE-XX-MKT.SLDDRW SCALE 4 : 1 PROPRIETARY NOTE THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PURPOSE OTHER THAN THAT WHICH IT WAS PHONE: 812-944-6733 FAX: 812-948-5047 OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. e-Mail: info SAMTEC.com code: 55322 NOTES: DESCRIPTION: SHEET SCALE: 2:1 1. NOTE DELETED100 C.L. SINGLE BEAM SOCKET STRIP 2. NOTE DELETED. DWG. NO. 3. NOTE DELETED. HLE-1XX-02-XX-DV-XE-XX 4. NOTE DELETED. BY: KEVIN B 10/27/99 SHEET OF2 2