IDSD-08-S-36.00 Samtec

F-219 IDMD24D12.00G (2.54 mm) .100 SLIM BODY FLAT RIBBON IDC CABLES Mates with: SPECIFICATIONS TYPE ROW NO. PINS END TSW, MTSW, TSM, EJH, STRIP OPTION PER ROW ASSEMBLY For complete specifications PHT, HMTSW, HTSW, see www.samtec.com IDSS, HW, DW, EW, ZW, MTLW www.samtec.com IDSD, www.samtec.com IDMS or IDSD Mates with: Single www.samtec.com IDMD TST, HTST, ZST, S = S End Insulator Material: = Single BST, EJH Black Glass Filled Polyester Plating: Au over 50 (1.27 m) Ni or D Sn over 100 (2.54 m) Cu = Double or 50 (1.27 m) Ni (Color coded Wire: IDM cable N/A for 28 AWG 7/36 stranded = Standard Tail Male Plug Tinned Copper 31 thru 36 Temperature Range: Socket or Male Plug on one end pins/row. -20 C to +105 C See G IDS (Rainbow Cable) option.) = Socket Double -40 C to +105 C = D End (Gray Cable) Contact (IDSS/IDSD): BeCu Terminal (IDMS/IDMD): Phosphor Bronze Current Rating (IDSD/TST): 02 thru 32 3.4 A per pin (2 pins powered) Current Rating (IDMD): DOUBLE 3 A per pin Full size (64 positions): IDMD IDMS (82.55) 3.250 (2 pins powered) Less than 64 positions: (Double) Lead Size Range: (Single) No. Positions/row X (2.54) .100 + (1.68) .066 (0.56 mm) .022 SQ to Socket or Male Plug on each end SINGLE (0.71 mm) .028 SQ Full size (32 positions): Lead Insertion Depth: (81.53) 3.210 Less than 32 positions: (5.59 mm) .220 to (2.54) (5.08) Transfer = No. Positions/row X (2.54) .100 + (0.71) .028 .100 .200 T (6.22 mm) .245 End RoHS Compliant: Yes (6.10) .240 MAX RECOGNITIONS (0.48) (3.18) For complete scope .019 .125 of recognitions see (0.46) (2.54) Male Plug on one end with socket on www.samtec.com/quality (2.54) .100 .018 .100 other. Begin part number with IDM. x (0.48) .019 (For square or long tail see HCMX Series) FILE NO. E111594 OTHER SOLUTIONS 02 thru 36 Molded-To-Position IDC Assemblies Low profile DOUBLE Full size (72 positions): Skinny side locks (92.71) 3.650 Less than 72 positions: Dual beam contacts IDSD IDSS No. Positions/row x (2.54) .100 + (1.50) .059 Single and double row (Double) (Single) SINGLE (3.05 mm) .120 Full size (36 positions): (91.69) 3.610 and (5.84 mm) .230 Less than 36 positions: (5.08) No. Positions/row x (2.54) .100 + (0.48) .019 .200 length tail available (9.27) .365 REF (0.76) (2.54) (2.54) .030 .100 .100 SQ Note: This Series is non-standard, non-returnable. Due to technical progress, all designs, specifications and components are subject to change without notice. WWW.SAMTEC.COM All parts within this catalog are built to Samtecs specifications. Customer specific requirements must be approved by Samtec and identified in a Samtec customer-specific drawing to apply.IDSD05D04.25S02 IDSD24S05.00 IDSS, IDSD, IDMS, IDMD SERIES SLIM BODY FLAT RIBBON IDC CABLES EJECTOR HEADERS ASSEMBLED OPTION & LOCKING CLIPS LENGTH IDSS or IDSD STRIP ASSEMBLY Ejector headers Locking clips XX.XX POLARIZING KEY LOCKING = Assembled Length CLIP .025 SQ (0.64) .025 Optional polarizing key for TERMINAL SQ PC use with IDSS & IDSD STRIP (TSW) Assembled Length in BOARD 1 (5.84) INCHES ( /8 ) Series. Also polarizes .230 (2 inches minimum) SSW, SSQ, ESW & ESQ Series. Black High See TSW Series. Temperature Thermoplastic Order: Part Number PK-01-06 See EJH Series. (Available in wheels of six each) Tin Plating = T (Both ends) ST X S XX RR = Stripped & Tinned = Daisy Chain Single = Re= Reverversedsed Tin IDM Specify Suffix from table. 2 10 (0.25 m) Gold IDS 1 C = XX 8 min. All dimensions are 1/16 . Single Row (-T End Assembly Required) Not available in 28 positions and higher. Connectors (IDSS) 10 (0.25 m) Gold IDM A = Tin IDS (-T End Assembly Required) Outer Most Standard plating is selective 4 minimum gold over BeCu contact for IDS When mating double row Selective gold over phosphor 8 connector with two single row bronze for IDM. 1 1/8 (3.18) ST8 connectors, the outer most 1/4 (6.35) ST4 single will be connected to M 1/2 (12.70) = Middle Reversed P XX ST2 Conductor 1 and the inside =Polarized 3/8 (9.53) ST3 single to Conductor 2. 4 7 72 04 02 D XX B XX = Daisy Chain, Double = Breakout 71 03 01 Specify XX as number of 2 1 XX 8 conductors to be broken out. Specify XX as position. For min. Requires SXX, WXX or DXX Double Row Double the same position will Connectors (IDSD or be polarized on both ends. 8 IDMD) (Not available on IDM unless transfer, then only the socket O Outer Most is polarized.) 2 XX = Outside Reversed 4 minimum G 5 max. 7 = Gray Cable 2 min. Breakout starts with Number 1 lead indicated Specify G for Gray cable. Gray W XX by brown wire or red stripe. cable has one red edge. IDSS = Wiring Reversed Shown on top side. 5 and IDMS uses .100 centerline Daisy Chain, Single cable. IDSD and IDMD uses .050 centerline cable. Cable is RW Same as S XX except outer = Reversed Wiring 28 AWG 7/36 copper wire. Requires SXX, WXX or DXX strip connected to Conductor Standard cable is same as 2 and inside strip connected above except color coded. 1 wire opposite position 1. to Conductor 1. 3 6 7 8 Due to technical progress, all designs, specifications and components are subject to change without notice. WWW.SAMTEC.COM All parts within this catalog are built to Samtecs specifications. Customer specific requirements must be approved by Samtec and identified in a Samtec customer-specific drawing to apply.