TFM-105-02-S-D-TR Samtec

F-219 (Rev 10DEC18) TFM11502LS TFM11002LDLC TFM11001LDRE1WT TFML11502LDK (1.27 mm) .050 SMT & THROUGH-HOLE HEADER Shrouded body for blind mating (1.27 mm x 1.27 mm) TFM Board Mates: SPECIFICATIONS .050 x .050 SFM, SFMC micro pitch For complete specifications and TFM Cable Mates: recommended PCB layouts SFSD see www.samtec.com TFM or www.samtec.com TFML TFML Board Mates: APPLICATIONS Insulator Material: SFML Black Liquid Crystal Polymer Terminal Material: TFM-DH Board Mates: Phosphor Bronze SFM (-DH), SFMC Plating: Au or Sn over 50 (1.27 m) Ni TFM-DH Cable Mates: Current Rating (TFM/SFM): SFSDX (-S, -D, -SR, -DR) 3.2 A per pin (2 pins powered) TFM-DH to SFM-DH SHOWN Voltage Rating: 250 VAC mated with SFM Operating Temp Range: 10 YEAR MFG -55 C to +125 C WITH 30 GOLD RoHS Compliant: EXTENDED LIFE Yes PRODUCT HIGH MATING Surface mount or CYCLES PROCESSING through-hole tails TFM to SFM-SH SHOWN Lead-Free Solderable: Yes SMT Lead Coplanarity: (0.10 mm) .004 max (05-25) (0.15 mm) .006 max (30-50)* TYPE NO. PINS PLATING *(.004 stencil solution LEAD STYLE 1 may be available contact STRIP PER ROW OPTION IPG samtec.com) RECOGNITIONS Specify L For complete scope 03, 04, 06, 08 of recognitions see = 15 (0.38 m) (TFM 01 & 02 only) LEAD STYLE TFM www.samtec.com/quality Gold on post, from chart = Standard Matte Tin on tail 05, 07, 10, 15, 20, (Call Samtec for FILE NO. E111594 E.L.P. plating option) 25, 30, 35, 40, 45, 50 TFML (Standard sizes) = Locking (01 & 02 lead style only) OTHER SOLUTIONS (1.27) .050 x MATED HEIGHTS Lower cost plating options. No. of Positions + (3.18) .125 (2.79) LEAD STYLE See TFC Series. MATED .110 HEIGHT* TFM SFM (4.45) (6.35) .250 .175 02 LEAD 12 (8.13) .320 01 STYLE B C 02 LEAD SINGLE ROW (9.91) .390 22 (T/H) (1.14) STYLE A (See website for DS & WT OAL) .045 (11.81) .465 01 (5.59) .220 (1.97) .078 (SMT) 32 REX = (1.27) .050 x LEAD STYLE (5.59) .220 (2.77) .109 02 (5.72) .225 MATED 03* No. of Positions + (6.68) .263 HEIGHT* (1.27) TFM SFM 12* (7.49) .295 11* (7.37) .290 (1.97) .078 02 (1.27) .050 (5.97) .235 .050 01 (9.27) .365 (7.37) .290 (2.77) .109 22* 13* DIA A (5.97) .235 (5.72) 03 32* (11.18) .440 21* (9.14) .360 (1.97) .078 (SMT or TH) .225 (7.75) .305 * N/A with 07, -DH or 11 23* (9.14) .360 (2.77) .109 -S row option 13 01 (7.75) .305 (11.05) .435 (1.97) .078 31* 01 (1.27) .050 (9.53) .375 * Not Available with 07 or -S row option 21 DOUBLE ROW (0.46) .018 DIA (9.53) .375 23 (11.43) .450 31 (1.40) *Processing conditions will .055 B A affect mated height. (2.35) (1.42) (0.64) .093 C (0.36) .014 .056 .025 Note: LC WT THROUGH-HOLE SURFACE MOUNT Some sizes, styles and (SMT or TH) (01 & 02 ONLY) options are non-standard, non-returnable. Due to technical progress, all designs, specifications and components are subject to change without notice. WWW.SAMTEC.COM All parts within this catalog are built to Samtecs specifications. Customer specific requirements must be approved by Samtec and identified in a Samtec customer-specific drawing to apply.TFM10501LDRA TFML15001LDLC TFM12501LDWT TFM11002LDH TFM11002LDDS TFM, TFML SERIES SMT & THROUGH-HOLE HEADER Shrouded body for (1.27 mm) blind mating .050 pitch Passes 10 Year MFG Locking option Surface mount or Locking clip option through-hole tails Weld tab option Mates with SFM for Screw down Screw down option coplanar mating Weld tab option option ROW OPTION OPTION Specify only RA, RE1 or RE2 Specify only A, LC, DS or WT SMT lead styles only S Not available with RA, RE1 and RE2 Specify only K or P = Single Row RA unless otherwise noted. (TFM only) = Right-angle K (Lead style 01 only) A = Polyimide Film Pick & Place Pad = Alignment Pin D = Double Row RE1 P = Right-angle Elevated for (1.58 mm) .062 PCB LC = Plastic Pick & Place Pad (Requires TFM lead style 01, D row and WT) = Locking Clip (5 positions minimum) DH* (Manual Placement required) (Not available with = Double Horizontal 5 position with WT) (TFM lead style 02 only) RE2 (05 thru 50 positions only) = Right-angle Elevated for (2.36 mm) .093 PCB DS Specify TR last (TR option only (Requires TFM lead style 01, D row and WT) = Dual Screw Down for available) (1.60 mm) .062 PCB TR (05, 07, 10, 15, 20, 25, 30, = Tape & Reel Note: The recommended -REX PCB board layout is different from the -RA. Contact IPG samtec.com 35, 40 positions only) (Not available with DS) before designing your board for specifications. (TFM lead styles 01 and 02 only) (Requires D row option) (Mates with SFMDS option and SFSD/SFSDT SS and DS option only) (Not available with A, LC, (0.76) WT, K, P, TR) .030 (1.91) (2.26) .075 .089 WT (1.27) DH* (0.51) .020 = Weld Tab .050 ALSO AVAILABLE RA (TFM lead styles 01 and 02 only) (MOQ Required) (Required callout for RE1 & RE2) (Mates to SFSS/SFSD SR and Solder nail option DR option only) Other sizes (6.48) (05, 07, 10, 15, 20, 25, 30, 35, .255 Other platings 40, 45, 50 positions only) (1.99) .079 (3.81) * Note: .150 Weld tab is standard on DH option. (1.91) (0.51) .020 No need to specify WT. DS .075 (D, 01 & 02 ONLY) RE1 & RE2 Due to technical progress, all designs, specifications and components are subject to change without notice. WWW.SAMTEC.COM All parts within this catalog are built to Samtecs specifications. Customer specific requirements must be approved by Samtec and identified in a Samtec customer-specific drawing to apply.