TFM-1XX-XX-X-S-XX NOTES: REVISION AG 1. REPRESENTS A CRITICAL DIMENSION. 2. MINIMUM PUSHOUT FORCE: 16 OZ FOR TERMINALS, 12 OZ FOR WELD TABS, OPTION No OF POSITIONS AND 8 OZ FOR LOCKING CLIPS. ALL POSITIONS AVAILABLE -A: ALIGNMENT PIN (USE TFM-XX-S-01-A) DO NOT 3. MEASURED FROM BEND. -02 THRU -50 (NOT AVAILABLE WITH -WT OPTION) SCALE FROM 4. MAXIMUM TERMINAL BURR: .003 .08 . (SEE FIG 5, SHEET 2) THIS PRINT 5. MAXIMUM HEIGHT VARIATION BETWEEN ANY TWO PINS: .005 .13 . -LC: LOCKING CLIP (USE LC-05-TM) 6. DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED, THE -LC OPTION (NOT AVAILABLE WITH -WT OPTION) IS NOT COMPATIBLE WITH AUTO PLACEMENT. SAMTEC RECOMMENDS (SEE FIG 7, SHEET 3) (SEE NOTE 6) MANUAL PLACEMENT FOR ALL ASSEMBLIES WITH THE -LC OPTION. LEAD STYLE -P: PICK AND PLACE PAD (USE PPP-15) -01: T-1R16-01-X-2 (SEE FIG 6, SHEET 2) THROUGH HOLE (ONLY AVAILABLE ON -08 THRU -50 POSITIONS) -02: T-1R16-01-X-2 -K: POLYIMIDE FILM (SEE FIG 3, SHEET 2) SURFACE MOUNT (USE K-DOT-.217-.313-.005) -03: T-1R16-10-X -WT: WELD TABS (USE WT-25-07-T) THROUGH HOLE ((No. OF POSITIONS x .050 1.27 ) (SEE FIG 4, SHEET 2) (AVAILABLE ON -02 THRU -30 POS ONLY) + .125 3.18 )REF (NOT AVAILABLE WITH -A OR -LC OPTIONS) PLATING SPECIFICATIONS -TR: TAPE & REEL ((No. OF POSITIONS x .050 1.27 ) (SEE SHEET 3, TAPE AND REEL VIEW) -S: 30 SELECTIVE GOLD IN CONTACT AREA, -SN: SOLDER NAIL (USE WT-27-03) + .025 .64 )REF MATTE TIN ON TAIL ** (NOT AVAILABLE WITH -A, -LC, OR -F: 3 FLASH GOLD IN CONTACT AREA, -WT OPTIONS) (SEE FIG 8, SHEET 3) .100 2.54 REF MATTE TIN ON TAIL -G: 30 GOLD IN CONTACT AREA, 3 GOLD ON TAIL BODY SPECIFICATION -L: 15 LIGHT GOLD IN CONTACT AREA, .105 2.67 REF .065 1.65 MATTE TIN ON TAIL -S: SINGLE ROW (USE TFM-XX-S-XX-XX) -H: 50 HEAVY GOLD IN CONTACT AREA, 3 GOLD ON TAIL 01 -T: MATTE TIN CONTACT AND TAIL .083 2.11 .050 1.27 REF .175 4.45 REF ** NOT TOOLED ((No. OF POSITIONS x .050 1.27 ) - .050 1.27 ) 2 MAX SWAY 2 MAX SWAY (EITHER DIRECTION) (EITHER DIRECTION) .018 0.46 REF .1635 4.153 REF .2200 5.588 REF REF .010 0.25 REF .003.003 .014 0.36 REF MAX SWAY 2 2 MAX SWAY (EITHER DIRECTION) (EITHER DIRECTION) ((No. OF POSITIONS x .050 1.27 ) - .050 1.27 ) SECTION TABLE 1 POSITION COPLANARITY IN-PROCESS -02 THRU -29 .004 .10 FIG 1 UNLESS OTHERWISE SPECIFIED, PROPRIETARY NOTE -030 THRU -39 .006 .15 (TFM-115-01-X-S-XX SHOWN) DIMENSIONS ARE IN INCHES. THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO -40 THRU -50 .008 .20 TOLERANCES ARE: SAMTEC, INC. AND SHALL NOT BE REPRODUCED DECIMALS ANGLES OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY .XX: .01 .3 2 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PURPOSE OTHER THAN THAT WHICH IT WAS .XXX: .005 .13 PHONE: 812-944-6733 FAX: 812-948-5047 OBTAINED WITHOUT THE EXPRESSED WRITTEN TABLE 2 .XXXX: .0020 .051 CONSENT OF SAMTEC, INC. e-Mail info SAMTEC.com code 55322 LEAD STYLE BODY MATERIAL: DO NOT SCALE DRAWING SHEET SCALE: 1:0.4 DESCRIPTION: -01 TFM-XX-S-01-XX .078 1.98 .131 3.33 .428 10.87 .303 7.70 INSULATOR: LCP, UL 94 V0, COLOR: BLACK .050 C.L. SINGLE ROW SHROUDED TERMINAL STRIP TERMINAL: PHOSPHOR BRONZE -02 TFM-XX-S-01-XX N/A .131 3.33 .428 10.87 .231 5.87 DWG. NO. -03 TFM-XX-S-01-XX .111 3.33 .139 3.53 .645 16.38 .356 9.04 TFM-1XX-XX-X-S-XX BY: D. SCHMELZ 8/21/2008 SHEET OF1 3 F: DWG MISC MKTG TFM-1XX-XX-X-S-XX-MKT.SLDDRWNOTE: R = OVERALL LENGTH REF REVISION AG S = ((R - .216 5.49 ) /2) .020 .51 2 MAX SWAY (EITHER DIRECTION) .021.010 0.520.254 .216 5.49 90 0 .226.006 5.740.152 SEE TABLE 1, SHT 1 (SEE TABLE 2, 7 SHT 1) FLUSH TO .012 0.30 MAX 2 MAX SWAY (SEE NOTE 3) (EITHER DIRECTION) .185 4.70 MAX 02 SECTION 03 01 ((No. OF POSITIONS x .050 1.27 ) -.050 1.27 ) (SEE TABLE 2, (TOL ACCUM .005 .13 OVER 50 POS.) SHT 1) FIG 2 SURFACE MOUNT (TFM-115-02-X-S-XX SHOWN) FIG 3 (DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1) -K: POLYIMIDE FILM PAD (TFM-115-02-X-S-K SHOWN) ((NO OF POSITIONS X .050 1.27 ) +.263 6.68 ) REF NOTE: M = (No. OF POSITIONS X .050 1.27 ) + .125 3.18 REF TFM-XX-S-01-WT WT-25-07-T WITH -WT M = (No. OF POSITIONS X .050 1.27 ) + .263 6.68 REF P = ((M - .375 9.53 ) /2) .020 .51 .093 2.36 (TYP) .010 0.25 .025 0.64 .175 4.45 REF (TYP) REF REF .375 9.53 2 MAX SWAY REF SECTION PPP-15 (EITHER DIRECTION) .050 1.27 ((No. OF POSITIONS x .050 1.27 ) FIG 4 + .154 3.91 ) -WT OPTION (TFM-114-01-X-S-WT SHOWN) SECTION (DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1) FIG 6 C L -P OPTION (TFM-115-02-X-S-P SHOWN) (DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1) (PAD TO BE POSITIONED ON CL AS SHOWN) .045 1.14 REF PROPRIETARY NOTE THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY 520 PARK EAST BLVD, NEW ALBANY, IN 47150 .050 1.27 PURPOSE OTHER THAN THAT WHICH IT WAS PHONE: 812-944-6733 FAX: 812-948-5047 OBTAINED WITHOUT THE EXPRESSED WRITTEN REF e-Mail info SAMTEC.com code 55322 CONSENT OF SAMTEC, INC. DESCRIPTION: ((No. OF POSITIONS x .050 1.27 ) DO NOT SCALE DRAWING .050 C.L. SINGLE ROW SHROUDED TERMINAL STRIP R.025 0.64 + .075 1.91 ) FIG 5 DWG. NO. -A OPTION SHEET SCALE: 2:1 TFM-1XX-XX-X-S-XX (TFM-115-02-X-S-A SHOWN) (DIFFERENT AS SHOWN, OTHERWISE SAME AS FIG 1) BY: D. SCHMELZ 8/21/2008 SHEET OF2 3 F: DWG MISC MKTG TFM-1XX-XX-X-S-XX-MKT.SLDDRW