9HV3612P3K001 Sanyo Denki

9HV type High Static Pressure Fan Features High Static Pressure and High Airflow This fan delivers a maximum static pressure of 1,400 Pa and a maximum airflow of 3 0.72 m /min. Compared with the current model,* the maximum static pressure has increased by 1.67 times and maximum airflow has increased by 1.04 times. Space-saving This fan provides the same cooling performance as our conventional 40 40 mm fans.** The reduced fan size enables enhanced design flexibility. High Energy Efficiency and Low Noise The PWM control function enables the external control of fan speed, contributing to lowering noise and improving energy efficiency of devices. * Current model: San Ace 36 9GX type 36 36 28 mm (9GX3612P3K001). ** Conventional fans: 40 40 28 mm San Ace 40 9GV type (9HV0412P3K001) and 9GAX type (9GAX0412P3S001). 363628 mm Specications The models listed below have ribs and pulse sensors with PWM control function. Operating PWM Operating Expected Rated voltage Rated current Rated input Rated speed Max. airow Max. static pressure SPL Model no. voltage range duty cycle* -1 3 temperature life V A W min m /min CFM Pa inchH O dB(A) 2 V % C h 100 1.75 21.0 32500 0.72 25.4 1400 5.62 67 -20 to +60 30000/60C 9HV3612P3K001 12 10.8 to 13.2 20 0.05 0.6 6000 0.12 4.2 47.2 0.19 26 * PWM frequency: 25 kHz. Fan does not rotate when PWM duty cycle is 0%. Models with the following sensor specications are also available as options: Without sensor Lock sensor Common Specications Material Frame: Plastic (Flammability: UL 94V-0),Impeller: Plastic (Flammability: UL 94V-1) Refer to specications Expected life (L10 life: 90% survival rate for continuous operation in free air at 60C, rated voltage) Current blocking function and reverse polarity protection Motor protection system 50/60 Hz, 500 VAC, for 1 minute (between lead wire conductors and frame) Dielectric strength Sound pressure level (SPL) At 1 m away from the air inlet Refer to specications (Non-condensing) Operating temperature -30 to +70C (Non-condensing) Storage temperature Lead wire Red Black Sensor Yellow Control Brown Approx. 53 g Mass Airow - Static Pressure Characteristics PWM Duty - Speed Characteristics Example PWM duty cycle Operating voltage range -1 (min ) (inch H2O) (Pa) (inch H2O) (Pa) 12 VDC PWM duty cycle 100% Voltage: 12 VDC 1600 1600 35000 PWM frequency: 25 kHz -1 6 6 32500 min PWM duty cycle 13.2 V 1400 1400 30000 100% 5 5 1200 1200 25000 12 V 4 1000 4 1000 20000 800 800 3 3 10.8 V 15000 50% 600 600 2 2 10000 400 400 20% 1 1 5000 200 200 0 0 3 3 (m /min) (m /min) 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0 100 (%) PWM duty cycle 0 5 10 15 20 25 (CFM) 0 5 10 15 20 25 (CFM) Airow Airow Static pressure Static pressure Speed PWM Input Signal Example Input signal waveform VIH V = 4.75 to 5.25 V V = 0 to 0.4 V IH IL T1 1 PWM duty cycle (%) = PWM frequency 25 (kHz) = 100 T T Current source (Isource) = 1 mA max. (when control voltage is 0 V) Current sink (Isink) = 1 mA max. (when control voltage is 5.25 V) VIL Control terminal voltage = 5.25 V max. (when control terminal is open) T1 When the control terminal is open, fan speed is the same as when PWM duty cycle is 100%. Either TTL input, open collector or open drain can be used for PWM control input signal. T Example of Connection Schematic DC fan input voltage Inside of DC fan 3 V 10 k Control 22 Isource PWM input signal Isink Specications for Pulse Sensors Output circuit: Open collector Output waveform (Need pull-up resistor) In case of steady running Inside of DC fan (One revolution) T 0 Sensor Pull-up resistor Pull-up voltage T1 T2 T3 T4 T (1/4) T 1 to 4 0 Ic T (1/4) T =60/4N (s) 1 to 4 0 VCE=Fan input voltage max. V OH -1 Ic=5 mA max. V =V (SAT)=0.6 V max. OL CE N=Fan speed (min ) Sensor output (VCE) V OL 0 V Dimensions (unit: mm) 4-3.50.3 Mounting hole +30 320 0 Lead wire AWG 24 (4) (4) 29.50.3 UL 1061 360.5 280.5 Rotating direction Airow direction Reference Dimensions of Mounting Holes and Vent Opening (unit: mm) Inlet side, Outlet side 35 29.50.3 (14.8) 4-3.7 4-R2.7 Notice Please read theSafety Precaution on our website before using the product. The products shown in this catalog are subject to Japanese Export Control Law. Diversion contrary to the law of exporting country is prohibited. For protecting fan bearings against electrolytic corrosion near strong electromagnetic noise sources, we provide effective countermeasures such as Electrolytic Corrosion Proof Fans and EMC guards. Contact us for details. 3-33-1, Minami-Otsuka, Toshima-ku, Tokyo 170-8451, Japan TEL: +81 3 5927 1020