DATASHEET Two-Stage Filters FN 2415 Single-phase EMC Filter for Control Equipment Filter for the control line of complex Approvals & Compliances equipment and machinery To ensure interference-free operation of control equipment (PLC, Motion-, Robot Control etc.) To improve operational reliability and system stability Compact EMC filter design with minimum space requirement Features and benefits An additional filter for the supply cables of controls of rather large and complex systems, to ensure a reliable operation of the control unit. To achieve significant system stability improvement Performance indicators by reducing the risk of internal interference propagation and coupling. FN 2415 B version without leakage current (0 mA) FN 2415 L version with leakage current of less than 3.5 mA. Simple and time-saving installation with good accessibility for automatic and hand tools Solid, touch-safe terminal blocks offering sufficient contacting cross section according to the EN 60204-1 installation standard By providing a very decent attenuation performance, FN 2415 contributes significantly to Technical specifications the achievement of electromagnetic compliance, e.g. EN50370-1 standards for machine tools. Maximum continuous operating voltage 250 VAC Operating frequency DC to 400 Hz Typical applications 6 to 16 A 50C Rated currents Ideal for industrial equipment, machinery and diverse High potential test voltage P/N > E 2250VDC for 2 sec process automation systems, which involve any kind P > N 1100VDC for 2 sec of control units (NC, CNC, Motion- and Robot IP 20 Protection category Controls). Overload capability 4x rated current at switch on, Large and complex machine tools with multiple 1.5x rated current for 1 minute, once per hour driving axes and very long motor cables can be -25C to +100C (25/100/21) Temperature range (operation and storage) subjected to major reliability problems, provoked and Flammability corresponding to UL 94 V-2 or better by internal coupling of interferences from the drive Design corresponding to UL 1283, CSA 22.2 No. 8 1986, IEC/EN 60939 system to the control wires. MTBF 50C/250 V (Mil-HB-217F) 1,300,000 hours This can cause drop outs and interrupts of the control unit and consequently lead to unnecessary downtimes of the entire machine. FN 2415 can also be used for most diverse single-phase applications, e.g. motor drives and power supplies. Typical electrical schematic2 EMC/EMI Products Schaffner Group Datasheets 24 Feb 2021 Filter selection table Filter Buy Rated current Leakage current* Power loss Inductance** Capacitance** Resistance** Input/Output Weight 40C (25C) 250VAC/50Hz L Cx Cy R (120VAC/60Hz) A mA W mH *** F nF k kg FN2415-6-29 6 (6.6) 7.85 (4.52) 2.2 8 3.3 100 220 -29 0.4 FN2415-10-29 10 (11) 7.85 (4.52) 2.4 4.2 3.3 100 220 -29 0.4 FN2415-16-29 16 (17.5) 7.85 (4.52) 4.3 3 3.3 100 220 -29 0.4 FN2415B-6-29 6 (6.6) 0.00 (0.00) 2.2 8 3.3 220 -29 0.4 FN2415B-10-29 10 (11) 0.00 (0.00) 2.4 4.2 3.3 220 -29 0.4 FN2415B-16-29 16 (17.5) 0.00 (0.00) 4.3 3 3.3 220 -29 0.4 FN2415L-6-29 6 (6.6) 2.59 (1.49) 2.2 8 3.3 33 220 -29 0.4 FN2415L-10-29 10 (11) 2.59 (1.49) 2.4 4.2 3.3 33 220 -29 0.4 FN2415L-16-29 16 (17.5) 2.59 (1.49) 4.3 3 3.3 33 220 -29 0.4 * Maximum leakage under normal operating conditions (acc. to IEC60939-3). Note: if the neutral line is interrupted, worst case leakage could reach twice this level. ** Tolerances apply: Inductance: -30/+50%, Capacitance: 20%, Resistance: 10% *** Value of both inductors in the same Typical filter attenuation Per CISPR 17 DM (differential mode) =50 /50 sym CM (common mode)=50 /50 asym 6 A: Standard type L type B type 10 A: Standard type L type B type 16 A: Standard type L type B type