FN261S-1-06-10 Schaffner

DATASHEET IEC Inlet Filters FN 9260 General Purpose Power Entry Module with Fuses Rated currents up to 10 A Approvals For one or two fuses Optional safety version (A type) Complies with IEC/EN 60601-1 Snap-in versions (S type) The FN 9260 power entry module combines an IEC inlet, mains filter with excellent filter attenuation and Performance indicators fuses in a small form factor. Choosing FN 9260 product line brings you rapid availability of a standard filter associated with the necessary safety acceptances. Standard IEC connector filters are a practical solution helping you to pass EMI system approval in a short time. A wide selection on amperage ratings, output connections, mounting possibilities and filters for medical applications are designed to offer you the desired solution. Features and Benefits Exceptional conducted attenuation performance, based on chokes with high saturation resistance Technical specifications and excellent thermal behavior B types comply with the requirements of IEC/EN Maximum continuous operating voltage 250 VAC, 50/60 Hz 60601-1 for creepage and clearance, leakage current Operating frequency DC to 400 Hz and high potential testing Rated currents 1 to 10 A 40C max. Versions up to 10 A are available with fuse holder for P > PE 2000 VAC for 2 sec (standard types) High potential test voltage one or two fuses P > PE 2500 VAC for 2 sec (B types) P > N 760 VAC for 2 sec (standard types) Custom-specific versions are available on request P > N 1700 VDC for 2 sec (B types) Protection category IP 40 according to IEC 60529 Typical applications Temperature range (operation and storage) -25C to +85C (25/85/21) Design corresponding to UL 1283, CSA 22.2 No. 8 1986, IEC/EN 60939 Portable electrical and electronic equipment Flammability corresponding to UL 94 V-2 or better Medical equipment MTBF 40C/230 V (Mil-HB-217F) 2,200,000 hours Small to medium-sized machines and household Fuse holder 1 or 2 fuses (5 x 20 mm) equipment Single-phase power supplies, switch-mode power supplies Test and measurement equipment Typical electrical schematic2 EMC/EMI Products Schaffner Group Datasheets 2017 Filter selection table Capacitance Filter Rated current Leakage current* Inductance Resistance Input/Output Fuses Weight 40C (25C) 250 VAC/50 Hz L Cx Cy R connections ( 120 VAC/60 Hz) A mA mH F nF k Qty g FN 9260 x-1-06-y 1 (1.2) 0.31 (0.18) 5.3 0.1 2.2 1000 -06 2 55 FN 9260 x-2-06-y 2 (2.3) 0.31 (0.18) 2.7 0.1 2.2 1000 -06 2 55 FN 9260 x-4-06-y 4 (4.6) 0.31 (0.18) 1.0 0.1 2.2 1000 -06 2 55 FN 9260 x-6-06-y 6 (6.9) 0.31 (0.18) 0.3 0.1 2.2 1000 -06 2 55 FN 9260 x-10-06-y 10 (11.5) 0.31 (0.18) 0.2 0.1 2.2 1000 -06 2 55 FN 9260 xA1-1-06-y 1 (1.2) 0.03 (0.02) 5.3 0.1 0.22 1000 -06 2 55 FN 9260 xA-2-06-y 2 (2.3) 0.07 (0.04) 2.7 0.1 0.47 1000 -06 2 55 FN 9260 xA-4-06-y 4 (4.6) 0.07 (0.04) 1.0 0.1 0.47 1000 -06 2 55 FN 9260 xA-6-06-y 6 (6.9) 0.07 (0.04) 0.3 0.1 0.47 1000 -06 2 55 FN9260 xA-10-06-y 10 (11.5) 0.07 (0.04) 0.2 0.1 0.47 1000 -06 2 55 FN 9260 xB-1-06-y 1 (1.2) 0.00 5.3 0.1 1000 -06 2 55 FN 9260 xB-2-06-y 2 (2.3) 0.00 2.7 0.1 1000 -06 2 55 FN 9260 xB-4-06-y 4 (4.6) 0.00 1.0 0.1 1000 -06 2 55 FN 9260 xB-6-06-y 6 (6.9) 0.00 0.3 0.1 1000 -06 2 55 FN9260 xB-10-06-y 10 (11.5) 0.00 0.2 0.1 1000 -06 2 55 FN 261 x-1-06-y 1 (1.2) 5.3 0.1 2.2 1000 -06 1 55 0.31 (0.18) FN 261 x-2-06-y 2 (2.3) 0.31 (0.18) 2.7 0.1 2.2 1000 -06 1 55 FN 261 x-4-06-y 4 (4.6) 0.31 (0.18) 1.0 0.1 2.2 1000 -06 1 55 FN 261 x-6-06-y 6 (6.9) 0.31 (0.18) 0.3 0.1 2.2 1000 -06 1 55 FN 261 x-10-06-y 10 (11.5) 0.31 (0.18) 0.2 0.1 2.2 1000 -06 1 55 * Leakage current under normal operating conditions (acc. to IEC60939-3). Note: if the neutral line is interrupted, worst case leakage could reach twice this level. Product selector For example: FN 9260-1-06-10, FN 9260 SB-10-06-20, FN 261 S-6-06-30