FN3311-400-99-C16-R55 Schaffner

DATASHEET 3-Phase Filters FN 3311/FN 3310 Compact power line AC EMC/EMI filter High current 3-phase filter up to 2300 A Approvals & Compliances Extremely compact and light weight design Minimum installation foot print Performance optimised for standard purpose applications FN 3310 series without Cy capacitors to ground FN 3311 IT versions for use in IT power networks The FN 3311/FN 3310 poduct series of standard EMC/ EMI filters are based on Schaffners many years of expertise in filter design for all types of converter and inverter applications. Installed between the PV inverter and the power grid, the FN 3311/FN 3310 AC Performance indicators filters are used to influence positively the conducted emissions on the grid side to help to comply with the required emission standards. Features and benefits The FN 3311/FN 3310 series are the most compact dedicated high current AC filters, not only suitable for PV applications, but being an optimum fit with most modern PV inverter topologies. In addition the filters can be configured in a very flexible way to fulfil custom specific application requirements. All FN 3311/FN 3310 come in unsymmetrical housings, which help to prevent inverse installation and wrong Technical specifications electrical connection. Along with solar panel-side installed Schaffner DC EMC/EMI filters FN 2211/FN Maximum continuous operating voltage 3x 520/300 VAC for FN 3311 2210, the AC filters FN 3311/FN 3310 are key to meet 3x 520 VAC for FN 3310 the stringent international standards for electro- Operating frequency DC to 60 Hz magnetic compatibility and help to ensure a reliable Rated currents 250 to 2300 A 50C and fault-free operation of the entire PV system. P > E 2 kVAC for 2 sec (FN 3311 IT 3 kVAC for 2 sec) High potential test voltage P > P 2.25 kVDC for 2 sec (FN 3311 IT 2.68 kVDC for Typical applications 2 sec) Protection category IP 00 The FN 3311/FN 3310 series are primarily designed for Overload capability 4x rated current at switch on, max. 8 sec all kind of power line connected converter and 1.5x rated current for 1 minute, once per hour inverter applications between 250 and 2 300 A. Temperature range (operation and storage) -40C to +100C However, they are optimised for PV inverter and can potentially also be applied for general purpose motor Climatic category 40/100/21 acc. to IEC 60068-1 drives applications. Terminals/Housing Ni plated cu bars/Metal UL 94V-0 Flammability corresponding to Design corresponding to UL 1283, CSA 22.2 No. 8, IEC/EN 60939, EN 60721-3 Typical electrical schematic FN 3311 MTBF Rated amb. Temp./Voltage (Mil- > 200,000 hours HB-217F) * - FN 3311 IT series without resistor to PE - FN 3310 series without resistor and capacitor to PE2 EMC/EMI Products Schaffner Group Datasheets 06 Jul 2021 Filter selection table Filters */** Rated current Typical inverter Leakage current**** Power losss Weight 50C AC power rating*** 520 VAC/50 Hz 25C/DC A kVA mA W kg FN 3311 with Cy caps FN 3311-250-99-C16-R55 or FN 3311 IT-250-99-C18-R5 250 170 0.06 18 2.3 FN 3311-400-99-C16-R55 or FN 3311 IT-400-99-C18-R5 400 270 0.06 30 3.1 FN 3311-600-99-C16-R55 or FN 3311 IT-600-99-C18-R5 600 400 0.06 33 4.0 FN 3311-1000-99-C16-R55 or FN 3311 IT-1000-99-C18-R5 1000 670 0.06 70 5.5 FN 3311-1500-99-C16-R55 or FN 3311 IT-1500-99-C18-R5 1500 1000 0.06 133 9.9 FN 3311-2300-99-C16-R55 or FN 3311 IT-2300-99-C18-R5 2300 1500 0.06 201 18.2 FN 3310 without Cy caps FN 3310-250-99-R5 250 170 18 2.3 FN 3310-400-99-R5 400 270 30 3.1 FN 3310-600-99-R5 600 400 33 4.0 FN 3310-1000-99-R5 1000 670 70 5.5 FN 3310-1500-99-R5 1500 1000 133 9.9 FN 3310-2300-99-R5 2300 1500 201 18.2 * Filters with higher current ratings available upon request. ** Filters with reduced Cy capacitance to ground for high asymmetrical currents and higher voltages available upon request. *** Calculated at rated current, 480 VAC (FN 3311)/690 VAC (FN 3311 HV) and cos phi=0.8. The exact value depends upon the efficiency of the drive, the motor and the entire application. **** Leakage current according IEC 60939-1 Typical filter attenuation FN 3311-xxx-99-C16-R55 Per CISPR 17 A=50 /50 sym B=50 /50 asym 250/400 A types 600 A types 1 000/1 500 A types 2 300A types Typical block schematic 1 PV modules 3 Central Inverter 5 Schaffner AC EMC/EMI filter FN 3xxx 2 Schaffner DC filter FN 22xx 4 Schaffner magnetic components Important note: depending on the grounding scheme of the solar power system, including the solar panel and the grid side transformer, the appropriate DC- and AC EMC/EMI filter version need to be selected. For support, please contact your local Schaffner sales office or partner.