FN 379-6/ Schaffner

DATASHEET IEC Inlet Filters FN 370 Versatile Filtered Power Entry Module Rated currents up to 6 A Approvals Single or dual-fuse holder Fuses 6.3 x 32 mm or 5 x 20 mm Voltage selector 100/120/230/240 V General purpose application Optional medical versions (B type) The FN 370 power entry module combines an IEC inlet, a mains filter with a single or dual- fuse holder and a voltage selector. Choosing FN 370 product line brings you the rapid availability of a standard filter associated with the necessary safety acceptances. Standard IEC connector filters are a practical solution helping you to pass EMI system approval in a short time. A wide selection on amperage ratings, fuse options, mounting possibilities and filters for medical applications are designed to offer you the desired solution. Features and benefits Good conducted attenuation performance, based on chokes with high saturation resistance and excellent thermal behavior Rear/front or snap-in mounting Technical specifications Single or dual-fuse holder USA 6.3 x 32mm or EU 5 x 20mm fuses Maximum continuous operating voltage 250 V, 50/60 Hz Operating frequency dc to 400 Hz Two attenuation performance ranges Rated currents 2 to 6 A 40 C max. Voltage selector 100/120/230/240 V High potential test voltage P > PE 2000 VAC for 2 sec (standard types) Custom-specific versions are available on request P > N 760 VAC for 2 sec P > PE 2500 VAC for 2 sec (B types) Typical applications Protection category IP40 according to IEC 60529 Temperature range (operation and storage) -25 C to +85 C (25/85/21) Portable electrical and electronic equipment Design corresponding to UL 1283, CSA 22.2 No. 8 1986, IEC/EN 60939 Consumer goods Flammability corresponding to UL 94 V-2 or better EDP and office equipment MTBF 40C/230V (Mil-HB-217F) 550,000 hours Single-phase power supplies, switch-mode power Voltage selector description VOL-SE 4SP-4 supplies Function Series/parallel Test and measurement equipment Voltage marking Medical equipment 1st 100 2nd 120 Typical electrical schematic 3rd 230 4th 240 Closed internal contact corresponding to 1st a, c, e 2st b, c, e 3st a, d 4st b, d * Other selected voltage marking on request. 2 EMC/EMI Products Schaffner Group Datasheets 2015 Filter selection table Filter* Rated current Leakage current** Inductance Capacitance Resistance Output Fuses*** Weight 40 C (25 C) 230 VAC/50 Hz L Cx Cy R connections A A mH nF nF k Qty g FN 370-2-2.1 2 (2.4) 373 0.70 47 2.2 13 1 55 FN 370-4-2.1 4 (4.8) 373 0.30 47 2.2 13 1 55 FN 370-6-2.1 6 (7.2) 373 0.18 47 2.2 13 1 55 FN 372-2-2.2 2 (2.4) 373 0.70 47 2.2 13 2 55 FN 372-4-2.2 4 (4.8) 373 0.30 47 2.2 13 2 55 FN 372-6-2.2 6 (7.2) 373 0.18 47 2.2 13 2 55 FN 376-2-2.1 2 (2.4) 373 0.70 47 2.2 13 1 55 FN 376-4-2.1 4 (4.8) 373 0.30 47 2.2 13 1 55 FN 376-6-2.1 6 (7.2) 373 0.18 47 2.2 13 1 55 FN 378-2-2.2 2 (2.4) 373 0.70 47 2.2 13 2 60 FN 378-4-2.2 4 (4.8) 373 0.30 47 2.2 13 2 60 FN 378-6-2.2 6 (7.2) 373 0.18 47 2.2 13 2 60 FN 379-2-2.2 2 (2.4) 373 2.00 47 2.2 13 2 70 FN 379-4-2.2 4 (4.8) 373 0.80 47 2.2 13 2 70 FN 379-6-2.2 6 (7.2) 373 0.50 47 2.2 13 2 70 FN 379B-2-2.2 2 (2.4) 2 2.00 47 1000 13 2 70 FN 379B-4-2.2 4 (4.8) 2 0.80 47 1000 13 2 70 FN 379B-6-2.2 6 (7.2) 2 0.50 47 1000 13 2 70 * Select the requested fuse holder for fuse EUR-1 or USA-1. ** Maximum leakage under normal operating conditions. Note: if the neutral line is interrupted, worst case leakage could reach twice this level. *** Filters are delivered without fuse. Product selector For example: FN 370-6-21, FN 378-4-22, FN 379B-2-22