FN5010- 10-99 Schaffner

Output filters FN 5010 Universal sine wave output filter for motor drives n Smoothing of PWM drive output voltage Approvals n Efficient motor protection n Increase of motor service life n Reduction of audible motor noise n Reduction of parasitic losses n Improvement of system reliability Technical specifications Typical electrical schematic Nominal operating voltage: 3x 400/230VAC 10% Motor frequency: 0 to 70Hz Switching frequency: 4 to 16kHz Rated currents: 2.5 to 610A 40C Motor cable length: 400m max. Impedance (uk): 10% nominal voltage, 50Hz & rated current Residual ripple voltage: <5% PE High potential test voltage: P > E 3000VAC for 3 sec P > P 2000VAC for 3 sec Protection category: IP00 (filters up to 150A according to VBG 4) Overload capability: 2x rated current at switch on for 30 seconds, 1.5x rated current for 1 minute, once per hour Temperature range (operation and storage): -25C to +85C (25/085/21) Insulation class: T40/F (155C) Flammability corresponding to: UL 94V-2 or better Design corresponding to: EN 61558-2-20 (VDE 0570-2-20) Features and benefits Typical applications n Conversion of the PWM output signal n Reduction of the pulse load of motor drive n Motor drive applications with long (symmetrical voltage components) of IGBTs and the parasitic losses on long motor cables motor drives into a smooth sine wave with shielded motor cables. n Pumps low residual ripple. n Cost-effective and space-saving open n Conveyors n Elimination of premature motor damage frame filter design. n HVAC applications caused by high dv/dt, overvoltages, motor n Vacuum impregnation ensures less n Elevators overheating and eddy current losses. humming noise and high durability. n General automation tasks n Significantly increased service life of n Applications with multiple motors electric motors. in parallel> Components > FN 5010 Filter selection table Filter Rated current Typical motor Nominal Nominal Typical Input/Output Weight 40C power rating* inductance capacitance power loss** connections Total Cu. Al. A kW mH F W kg kg kg FN 5010-2.5-99 2.5 1.1 22.4 1.5 50 -99 2.6 0.68 FN 5010-4.5-99 4.5 2.2 11 1.5 66 -99 3 1.1 FN 5010-8-99 8 4 7.2 1.5 73 -99 6.6 2.2 FN 5010-10-99 10 5.5 4.2 1.5 91 -99 6.6 2.6 FN 5010-13-99 13 7.5 4.2 1.5 124 -99 7.3 3.2 FN 5010-18-99 18 11 3.5 1.5 144 -99 11.5 3.6 FN 5010-24-99 24 15 2.4 1.5 191 -99 14 5 FN 5010-32-99 32 18.5 2 2 273 -99 16 6.8 FN 5010-42-99 42 22 1.58 7 Y 252 -99 22 7.4 FN 5010-48-99 48 30 1.5 7 Y 340 -99 28 8.8 FN 5010-60-99 60 30 1.1 4 290 -99 35 10.9 FN 5010-75-99 75 37 0.9 4 340 -99 42 11.5 FN 5010-90-99 90 45 0.8 5 360 -99 46 12.8 FN 5010-110-99 110 55 0.7 5 400 -99 58 13 FN 5010-150-99 150 75 0.5 7 716 -99 75 14.8 FN 5010-180-99 180 90 0.4 10 820 -99 88 1.4 10.9 FN 5010-210-99 210 110 0.4 10 1065 -99 115 2.1 11.2 FN 5010-270-99 270 132 0.3 12 1230 -99 150 2.1 14 FN 5010-325-99 325 160 0.3 12 1820 -99 194 5.2 21 FN 5010-410-99 410 200 0.2 18 1830 -99 206 5.2 23.8 FN 5010-510-99 510 315 0.17 20 2255 -99 290 6.5 32 FN 5010-610-99 610 355 0.14 25 2520 -99 330 7.7 37.5 * General purpose four-pole (1500r/min) AC induction motor rated 400V/50Hz. ** Exact value depends upon the motor cable type and length, switching frequency, motor frequency and further stray parameters within the system. Typical block schematic PE PE PE