FN9226B-10-02 Schaffner

DATASHEET IEC Inlet Filters FN9226 HF Performance EMC/EMI Filter Rated currents up to 10 A Approvals & Compliances Faston connection Optional PCB through hole connection Good HF coupling to the equipment housing Optional medical versions (B type) The FN 9226 IEC inlet filter combines an IEC inlet and mains filter with excellent filter attenuation in a small Performance indicators form factor. The FN 9226 is designed for printed circuit board mounting with good HF coupling to the equipment housing. Choosing the FN 9226 power entry module brings you the rapid availability of a standard filter associated with the necessary safety acceptances. Standard IEC connector filters are a practical solution helping you to pass EMI system approval in a short time. A wide selection on current ratings, output connections and low leakage versions for medical applications helps you to select the desired solution for your application. Features and benefits Technical specifications High conducted attenuation performance, based on chokes with high saturation resistance and Maximum continuous operating voltage 250 VAC, 50/60 Hz excellent thermal behavior Operating frequency DC to 400 Hz Rear flange mounting 1 to 10 A 50C max. Rated currents FN 9226 B versions comply with the requirements of Approvals by rated current 1 to 10 A (ENEC, UL, CSA) 1MOP acc. to IEC/EN 60601-1 for creepage and High potential test voltage P > PE 2000 VAC for 2 sec (standard types) clearance, leakage current and high potential P > N 760 VAC for 2 sec testing P > PE 2500 VAC for 2 sec (B types) Faston connection or PCB through hole pins Protection category IP 40 according IEC 60529 Temperature range (operation and storage) -25C to +85C (25/85/21) Good HF coupling UL 1283, CSA 22.2 No. 8 1986, IEC/EN 60939 Design corresponding to Rated currents up to 10 A Flammability corresponding to UL 94 V-2 or better Custom-specific versions are available on request MTBF 40C/230 V (Mil-HB-217F) 800,000 hours Typical applications Portable electrical and electronic equipment Small to medium-sized machines and household equipment Single-phase power supplies, switch-mode power supplies Consumer goods Test and measurement equipment EDP and office equipment Medical equipment Rack mounting equipment Typical electrical schematic2 EMC/EMI Products Schaffner Group Datasheets 05 Jan 2022 Filter selection table Filter Rated current Leakage current* Inductance Capacitance Resistance Output connections Weight 50C (25C) 250 VAC/50 Hz L Cx Cy R ( 120 VAC/60 Hz) A mA mH nF nF k g FN 9226-1-.. 1 (1.2) 0.31 (0.18) 4.65 47.0 2.2 -02 -06 40 FN 9226-3-.. 3 (3.5) 0.31 (0.18) 1.24 47.0 2.2 -02 -06 40 FN 9226-6-.. 6 (7.2) 0.31 (0.18) 0.52 47.0 2.2 -02 -06 40 FN 9226-10-.. 10 (11.6) 0.31 (0.18) 0.27 47.0 2.2 -02 -06 40 FN 9226 B-1-.. 1 (1.2) 0.00 4.65 47.0 2200 -02 -06 40 FN 9226 B-3-.. 3 (3.5) 0.00 1.24 47.0 2200 -02 -06 40 FN 9226 B-6-.. 6 (7.2) 0.00 0.52 47.0 2200 -02 -06 40 FN 9226 B-10-.. 10 (11.6) 0.00 0.27 47.0 2200 -02 -06 40 * Maximum leakage under normal operating conditions (acc. to IEC60939-3). Note: if the neutral line is interrupted, worst case leakage could reach twice this level. Product selector For example: FN 9226-6-02, FN 9226 B-10-06 Typical filter attenuation Per CISPR 17 A=50 /50 sym B=50 /50 asym C=0.1 /100 sym D=100 /0.1 sym 1 and 3 A types 6 to 10 A types