FN9244SR-1-06-20 Schaffner

DATASHEET IEC Inlet Filters FN 9244 Excellent Performance EMC/EMI Filter Superior attenuation performance Approvals Optional earth line choke Complies with IEC/EN 60601-1 Snap-in versions (S and S1 type) Hot inlet versions (HI type) (CQC except HI-types) Performance indicators The FN 9244 IEC inlet filter combines an IEC inlet and mains filter with superior filter attenuation in a small form factor. Choosing the FN 9244 product line brings you the rapid availability of a standard filter associated with the necessary safety acceptances. Standard IEC connector filters are a practical solution helping you to pass EMI system approval in a short time. A wide selection on amperage ratings, output connections, mounting possibilities and filters for medical applications are designed to offer you the desired solution. Features and benefits Technical specifications Exceptional conducted attenuation performance, based on chokes with high saturation resistance Maximum continuous operating voltage 250 VAC, 50/60 Hz and excellent thermal behavior Operating frequency DC to 400 Hz Rear/front or snap-in mounting Rated currents 1 to 15 A 50C max. Standard or wide mounting flange 1 to 10 A (ENEC, CQC) Approvals by rated current 1 to 15 A (UL, CSA) FN 9244 B versions comply with the requirements of 1MOP acc. to IEC/EN 60601-1 for creepage and High potential test voltage P > PE 2000 VAC for 2 sec (standard types) P > PE 2500 VAC for 2 sec (B types) clearance, leakage current and high potential P > N 1000 VAC for 2 sec testing Protection category IP 40 according to IEC 60529 Optional earth line choke see FN 9244 E data sheet Temperature range (operation and storage) -25C to +85C (25/85/21) Custom-specific versions are available on request Design corresponding to UL 1283, CSA 22.2 No. 8 1986, IEC/EN 60939 Flammability corresponding to UL 94 V-2 or better Typical applications MTBF 40C/230 V (Mil-HB-217F) 8 A: 2,035,000 hours 15 A: 1,035,000 hours Portable electrical and electronic equipment Small to medium-sized machines and household equipment Single-phase power supplies, switch-mode power supplies Test and measurement equipment Medical devices (MDD) In-vitro diagnostic medical devices (IVDD) Rack mounting equipment Typical electrical schematic2 EMC/EMI Products Schaffner Group Datasheets 09 Jul 2019 Filter selection table Filter Rated current Leakage current* Inductance Capacitance Resistance Output Weight 50C (25C) 250 VAC/50 Hz L Cx Cy R connections ( 120 VAC/60 Hz) A mA mH F nF k g FN 9244 x-1-06 1 (1.2) 0.31 (0.18) 59.53 0.1 2.2 -06 38 FN 9244 x-3-06 3 (3.5) 0.31 (0.18) 13.45 0.1 2.2 -06 38 FN 9244 x-6-06 6 (7.2) 0.31 (0.18) 4.1 0.1 2.2 -06 38 FN 9244 x-8-06 8 (10.6) 0.31 (0.18) 2.3 0.1 2.2 -06 38 FN 9244 x-10-06 10 (11.6) 0.31 (0.18) 1.02 0.1 2.2 -06 38 FN 9244 x-12-06 12 (12) 0.31 (0.18) 0.58 0.1 2.2 -06 38 FN 9244 x-15-06 15 (15) 0.31 (0.18) 0.4 0.1 2.2 -06 38 FN 9244 x-12-06HI 12 (12) 0.31 (0.18) 0.58 0.1 2.2 -06 38 FN 9244 x-15-06HI 15 (15) 0.31 (0.18) 0.4 0.1 2.2 -06 38 FN 9244 xR-1-06 1 (1.2) 0.31 (0.18) 59.53 0.1 2.2 1000 -06 38 FN 9244 xR-3-06 3 (3.5) 0.31 (0.18) 13.45 0.1 2.2 1000 -06 38 FN 9244 xR-6-06 6 (7.2) 0.31 (0.18) 4.1 0.1 2.2 1000 -06 38 FN 9244 xR-8-06 8 (10.6) 0.31 (0.18) 2.3 0.1 2.2 1000 -06 38 FN 9244 xR-10-06 10 (11.6) 0.31 (0.18) 1.02 0.1 2.2 1000 -06 38 FN 9244 xR-12-06 12 (12) 0.31 (0.18) 0.58 0.1 2.2 1000 -06 38 FN 9244 xR-15-06 15 (15) 0.31 (0.18) 0.4 0.1 2.2 1000 -06 38 FN 9244 xR-12-06HI 12 (12) 0.31 (0.18) 0.58 0.1 2.2 1000 -06 38 FN 9244 xR-15-06HI 15 (15) 0.31 (0.18) 0.4 0.1 2.2 1000 -06 38 FN 9244 xB-1-06 1 (1.2) 0.00 59.53 0.1 1000 -06 38 FN 9244 xB-3-06 3 (3.5) 0.00 13.45 0.1 1000 -06 38 FN 9244 xB-6-06 6 (7.2) 0.00 4.1 0.1 1000 -06 38 FN 9244 xB-8-06 8 (10.6) 0.00 2.3 0.1 1000 -06 38 FN 9244 xB-10-06 10 (11.6) 0.00 1.02 0.1 1000 -06 38 FN 9244 xB-12-06 12 (12) 0.00 0.58 0.1 1000 -06 38 FN 9244 xB-15-06 15 (15) 0.00 0.4 0.1 1000 -06 38 FN 9244 xB-12-06HI 12 (12) 0.00 0.58 0.1 1000 -06 38 FN 9244 xB-15-06HI 15 (15) 0.00 0.4 0.1 1000 -06 38 * Maximum leakage under normal operating conditions (acc. to IEC60939-3). Note: if the neutral line is interrupted, worst case leakage could reach twice this level. Typical filter attenuation Per CISPR 17 A=50 /50 sym B=50 /50 asym C=0.1 /100 sym D=100 /0.1 sym 1 and 3 A types 6 to 10 A types 12 and 15 A types