FN9246-15-06 Schaffner

DATASHEET IEC Inlet Filters FN 9246 High Performance IEC Inlet Filter Rated currents up to 20 A Approvals Optional medical versions (B type) Rear mounting Excellant attenuation in the lower frequency range The FN 9246 IEC inlet filter combines an IEC inlet and mains filter with excellent filter attenuation in a small form factor. Choosing the FN 9246 product line brings you the rapid availability of a standard filter associated with the necessary safety acceptances. Standard IEC connector filters are a practical solution helping you to pass EMI system approval in a short time. A wide selection on current ratings and low leakage versions for medical applications are Technical specifications designed to offer you the desired solution. Maximum continuous operating voltage 250 VAC, 50/60 Hz Features and benefits Operating frequency dc to 400 Hz Excellent conducted attenuation performance, Rated currents 1 to 20 A 50 C based on chokes with high saturation resistance Approvals by rated current 1 to 10 A (Semko) and excellent thermal behavior 16 A (Semko) for 16 and 20 A types Rear mounting 1 to 20 A (UL, CSA) Optional low leakage current versions for medical High potential test voltage P > PE 2000 VAC for 2 sec (standard types) applications P > PE 2500 VAC for 2 sec (B types) Rated currents up to 20 A P > N 1100 VAC for 2 sec (1 to 10 A types) P > N 1100 VDC for 2 sec (16 and 20 A types) Custom-specific versions are available on request Protection category IP40 according to IEC 60529 Temperature range (operation and storage) -25 C to +85 C (25/85/21) Typical applications Design corresponding to UL 1283, CSA 22.2 No. 8 1986, IEC/EN 60939 Electrical and electronic equipment Flammability corresponding to UL 94 V-2 or better Small to medium-sized machines and household MTBF 40C/230V (Mil-HB-217F) 1,600,000 hours equipment Single-phase power supplies, switch-mode power supplies Test and measurement equipment Building automation Medical equipment Lighting application Typical electrical schematic2 EMC/EMI Products Schaffner Group Datasheets 2014 Filter selection table Filter Rated current Leakage current* I nductance Capacitance Resistance Output connections Weight 40 C (25 C) 230 VAC/50 Hz L Cx Cy R A A mH F nF k g FN 9246-1-06 1 (1.2) 373 50 1.22 2.2 470 -06 140 FN 9246-3-06 3 (3.5) 373 14 1.22 2.2 470 -06 140 FN 9246-6-06 6 (7.2) 373 7 1.22 2.2 470 -06 140 FN 9246-10-06 10 (12) 373 3 1.22 2.2 470 -06 140 FN 9246-12-06 12 (14) 373 1.85 1.22 2.2 470 -06 140 FN 9246-15-06 15 (18) 373 0.89 1.22 2.2 470 -06 140 FN 9246-16-06 16 (18.5) 797 2.5 1.22 4.7 470 -06 275 FN 9246-20-06 20 (23) 797 1.5 1.22 4.7 470 -06 275 FN 9246B-1-06 1 (1.2) 2 50 1.22 470 -06 140 FN 9246B-3-06 3 (3.5) 2 14 1.22 470 -06 140 FN 9246B-6-06 6 (7.2) 2 7 1.22 470 -06 140 FN 9246B-10-06 10 (11.6) 2 3 1.22 470 -06 140 FN 9246B-12-06 12 (14) 2 1.85 1.22 470 -06 140 FN 9246B-15-06 15 (18) 2 0.89 1.22 470 -06 140 FN 9246B-16-06 16 (18.5) 2 2.5 1.22 470 -06 275 FN 9246B-20-06 20 (23) 2 1.5 1.22 470 -06 275 * Maximum leakage under normal operating conditions. Note: if the neutral line is interrupted, worst case leakage could reach twice this level. Typical filter attenuation Per CISPR 17 A = 50 /50 sym B = 50 /50 asym C = 0.1 /100 sym D = 100 /0.1 sym 1 A types 3 to 10 A types 12 and 15 A types 16 and 20 A types Product selector For example: FN 9246-6-06, FN 9246B-10-06