FN9246-6-06 Schaffner

DATASHEET IEC Inlet Filters FN9246 High Performance IEC Inlet Filter Rated currents up to 20 A Approvals & Compliances Optional medical versions (B type) Rear mounting Excellant attenuation in the lower frequency range The FN 9246 IEC inlet filter combines an IEC inlet and mains filter with excellent filter attenuation in a small Performance indicators form factor. Choosing the FN 9246 product line brings you the rapid availability of a standard filter associated with the necessary safety acceptances. Standard IEC connector filters are a practical solution helping you to pass EMI system approval in a short time. A wide selection on current ratings and low leakage versions for medical applications are designed to offer you the desired solution. Features and benefits Excellent conducted attenuation performance, based on chokes with high saturation resistance and excellent thermal behavior Technical specifications Rear mounting Maximum continuous operating voltage 250 VAC, 50/60 Hz FN 9246 B versions comply with the requirements of 1MOP acc. to IEC/EN 60601-1 for creepage and Operating frequency DC to 400 Hz clearance, leakage current and high potential Rated currents 1 to 20 A 50C testing 1 to 10 A (Semko) Approvals by rated current 16 A (Semko) for 16 and 20 A types Rated currents up to 20 A 1 to 20 A (UL, CSA) Custom-specific versions are available on request High potential test voltage P > PE 2000 VAC for 2 sec (standard types) P > PE 2500 VAC for 2 sec (B types) P > N 1100 VAC for 2 sec (1 to 10 A types) Typical applications P > N 1100 VDC for 2 sec (16 and 20 A types) Electrical and electronic equipment Protection category IP 40 according to IEC 60529 Temperature range (operation and storage) -25C to +85C (25/85/21) Small to medium-sized machines and household equipment UL 1283, CSA 22.2 No. 8 1986, IEC/EN 60939 Design corresponding to Single-phase power supplies, switch-mode power Flammability corresponding to UL 94 V-2 or better supplies MTBF 40C/230 V (Mil-HB-217F) 1,600,000 hours Test and measurement equipment Building automation Medical equipment Lighting application Typical electrical schematic2 EMC/EMI Products Schaffner Group Datasheets 05 Jan 2022 Filter selection table Filter Rated current Leakage current* Inductance Capacitance Resistance Output connections Weight 40C (25C) 250 VAC/50 Hz L Cx Cy R ( 120 VAC/60 Hz) A mA mH F nF k g FN 9246-1-06 1 (1.2) 0.31 (0.18) 50 1.22 2.2 470 -06 140 FN 9246-3-06 3 (3.5) 0.31 (0.18) 14 1.22 2.2 470 -06 140 FN 9246-6-06 6 (7.2) 0.31 (0.18) 7 1.22 2.2 470 -06 140 FN 9246-10-06 10 (12) 0.31 (0.18) 3 1.22 2.2 470 -06 140 FN 9246-12-06 12 (14) 0.31 (0.18) 1.85 1.22 2.2 470 -06 140 FN 9246-15-06 15 (18) 0.31 (0.18) 0.89 1.22 2.2 470 -06 140 FN 9246-16-06 16 (18.5) 0.66 (0.38) 2.5 1.22 4.7 470 -06 275 FN 9246-20-06 20 (23) 0.66 (0.38) 1.5 1.22 4.7 470 -06 275 FN 9246 B-1-06 1 (1.2) 0.00 50 1.22 470 -06 140 FN 9246 B-3-06 3 (3.5) 0.00 14 1.22 470 -06 140 FN 9246 B-6-06 6 (7.2) 0.00 7 1.22 470 -06 140 FN 9246 B-10-06 10 (11.6) 0.00 3 1.22 470 -06 140 FN 9246 B-12-06 12 (14) 0.00 1.85 1.22 470 -06 140 FN 9246 B-15-06 15 (18) 0.00 0.89 1.22 470 -06 140 FN 9246 B-16-06 16 (18.5) 0.00 2.5 1.22 470 -06 275 FN 9246 B-20-06 20 (23) 0.00 1.5 1.22 470 -06 275 * Maximum leakage under normal operating conditions (acc. to IEC60939-3). Note: if the neutral line is interrupted, worst case leakage could reach twice this level. Typical filter attenuation Per CISPR 17 A=50 /50 sym B=50 /50 asym C=0.1 /100 sym D=100 /0.1 sym 1 A types 3 to 10 A types 12 and 15 A types 16 and 20 A types Product selector For example: FN 9246-6-06, FN 9246 B-10-06