FN9255EB-15-06 Schaffner

DATA SHEET IEC Inlet Filters FN9255E High Performance dual-stage IEC C14 inlet filter with earth line choke Rated currents up to 15 A Approvals & Compliances Excellent performance/size ratio Earth line choke Version IEC C14 inlet acc. IEC 60320-1 Medical versions (B type) acc. to IEC/EN 60601-1 Snap-in and rear mount versions (S and M type) The FN9255 E IEC inlet filter incorporates a dual stage filter with Earth line choke into an IEC inlet that offers excellent filter attenuation in a compact housing. Using an IEC inlet, at the point of entry offers an optimized position and practical solution for integrating an EMC filter into any system. A wide selection of current ratings, output connections and mounting possibilities are Performance indicators available. The E Version of this family complies to medical application and safety requirements, with enhanced performance without added leakage current. Features and Benefits Exceptional attenuation performance from 150kHz to 300MHz due to dual-stage design High saturation resistance and excellent thermal behavior FN 9255 B versions comply with the requirements of 1MOP acc. to IEC/EN 60601-1 for creepage and clearance, leakage current and high potential testing Technical Specifications Suitable for IEC/EN 55014 tests up to 300MHz Rear and Front flange or snap-in mounting 250 VAC, 50/60 Hz Maximum continuous operating voltage options Operating frequency DC to 400 Hz Earth line choke Version, for standard version see ENEC and CQC: 2 to 10 A Approvals by rated current FN 9255 UL: 2 to 15A All versions according IEC/EN 62368-1 P > PE 2500 VAC for 2 sec High potential test voltage P > N 760 VAC for 2 sec Typical Applications IP 40 according to IEC 60529 Protection category Temperature range (operation and storage) -25C to +85C (25/85/21) Medical devices (MDD) UL 60939-3, CSA Std C22.2 No. 8, IEC/EN 60939-3, GB/T Design corresponding to Household and similar products as per IEC/EN 15287, GB/T 15288 55014 2 to 15 A Rated currents Test and measurement equipment Flammability according to UL 94 V-0 In-vitro diagnostic medical devices (IVDD) > 1,000,000 hours MTBF Rated amb. Temp./Voltage (Mil- Portable electrical and electronic equipment HB-217F) Small to medium-sized machines and household equipment Single-phase power supplies, switch-mode power supplies (SMPS) Typical electrical schematic2 IEC Inlet Filters Schaffner Group DATA SHEET 06. Jul 2022 Filter Selection Table Filter Rated current Leakage current* Inductance Capacitance Resistance Output 40C 250 VAC/50 Hz L1 L2 L3 Cx R connections ( 120 VAC/60 Hz) ** A mA mH H mH F k g 2 - 4.8 18 0.4 0.1 1000 -06 -07 66 FN 9255 ExB-2-06 4 - 2.1 18 0.4 0.1 1000 -06 -07 66 FN 9255 ExB-4-06 6 - 0.9 18 0.4 0.1 1000 -06 -07 66 FN 9255 ExB-6-06 10 - 0.2 18 0.4 0.1 1000 -06 -07 68 FN 9255 ExB-10-06 15 - 0.13 8 0.1 0.1 1000 -06 -07 68 FN 9255 ExB-15-06 Test conditions: 25C2C Measuring frequency for Inductance: 1 kHz 50 mV Tolerances: Inductance: +50%, -30% Capacitance: 25% Resistor: 15% For mechanical tolerances refer to mechanical data section. ** Maximum leakage under normal operating conditions (acc. to IEC60939-3). Note: if the neutral line is interrupted, worst case leakage could reach twice this level. ** Standard length is 100 mm Typical Filter Attenuation Per CISPR 17 symmetrical 50 /50 - Differential Mode (DM) asymmetrical 50 /50 - Common Mode (CM) 2 A type 4 A type 6 A type 10 A type 15 A type Product selector For example: FN 9255 EB-15-06, 15A Version with fast-on terminals FN 9255 ESB-10-06, 10A Version with fast-on terminals, snap-in version FN 9255 EMB-2-07, 2A Version with wire leads, rear mount version