FN9260B-2-07 Schaffner

DATASHEET IEC Inlet Filters FN9260 / FN261 General Purpose Power Entry Module with Fuses Rated currents up to 10 A Approvals & Compliances Integrated single/dual fuse holder Optional reduced leakage current versions (A/B type) Complies with IEC/EN 60601-1 Snap-in versions (S type) Good attenuation performance NEW: Wire leads option The FN9260 power entry module combines an IEC inlet, mains filter with excellent filter attenuation and fuses in a small form factor. Choosing FN9260 product line brings you rapid availability of a standard filter associated with the necessary safety acceptances. Standard IEC connector filters are a Performance indicators practical solution helping you to pass EMI system approval in a short time. A wide selection on amperage ratings, output connections, mounting possibilities and filters for medical applications are designed to offer you the desired solution. Features and Benefits Exceptional conducted attenuation performance, based on chokes with high saturation resistance and excellent thermal behavior FN9260 B versions comply with the requirements of 1MOP acc. to IEC/EN 60601-1 for creepage and Technical specifications clearance, leakage current and high potential testing Maximum continuous operating voltage 250 VAC, 50/60 Hz Versions up to 10 A are available with fuse holder for Operating frequency DC to 400 Hz one or two fuses Rated currents 1 to 10 A 40C max. Custom-specific versions are available on request High potential test voltage P > PE 2000 VAC for 2 sec (standard types) P > PE 2500 VAC for 2 sec (B types) P > N 760 VAC for 2 sec Typical applications Protection category IP 40 according to IEC 60529 Portable electrical and electronic equipment Temperature range (operation and storage) -25C to +85C (25/85/21) Medical equipment Design corresponding to UL 60939-3, CSA Std C22.2 No. 8-13, IEC/EN 60939-3, GB/T15287, GB/T15288 Small to medium-sized machines and household Flammability corresponding to Inlet plastic: UL 94 V-0 equipment Fuseholder plastic: UL 94 V-0 Single-phase power supplies, switch-mode power MTBF 40C/230 V (Mil-HB-217F) 2,200,000 hours supplies Fuse holder 1 or 2 fuses (5 x 20 mm) (certified to IEC 60127-6) Test and measurement equipment Typical electrical schematic2 EMC/EMI Products Schaffner Group Datasheets 05 Jan 2022 Filter selection table Output Filter Buy Rated current Leakage current* Inductance** Capacitance** Resistance** connections Fuses*** Weight 40C (25C) 250 VAC/50 Hz L Cx Cy R ( 120 VAC/60 Hz) A mA mH F nF k Qty g FN9260v-1-yy-zz 1 (1.2) 0.31 (0.18) 5.3 0.1 2.2 1000 -06 -07 2 55 FN9260v-2-yy-zz 2 (2.3) 0.31 (0.18) 2.7 0.1 2.2 1000 -06 -07 2 55 FN9260v-4-yy-zz 4 (4.6) 0.31 (0.18) 1.0 0.1 2.2 1000 -06 -07 2 55 FN9260v-6-yy-zz 6 (6.9) 0.31 (0.18) 0.3 0.1 2.2 1000 -06 -07 2 55 FN9260v-10-yy-zz 10 (11.5) 0.31 (0.18) 0.2 0.1 2.2 1000 -06 -07 2 55 FN9260vA1-1-yy-zz 1 (1.2) 0.03 (0.02) 5.3 0.1 0.22 1000 -06 -07 2 55 FN9260vA-2-yy-zz 2 (2.3) 0.07 (0.04) 2.7 0.1 0.47 1000 -06 -07 2 55 FN9260vA-4-yy-zz 4 (4.6) 0.07 (0.04) 1.0 0.1 0.47 1000 -06 -07 2 55 FN9260vA-6-yy-zz 6 (6.9) 0.07 (0.04) 0.3 0.1 0.47 1000 -06 -07 2 55 FN9260vA-10-yy-zz 10 (11.5) 0.07 (0.04) 0.2 0.1 0.47 1000 -06 -07 2 55 FN9260vB-1-yy-zz 1 (1.2) 0.00 5.3 0.1 1000 -06 -07 2 55 FN9260vB-2-yy-zz 2 (2.3) 0.00 2.7 0.1 1000 -06 -07 2 55 FN9260vB-4-yy-zz 4 (4.6) 0.00 1.0 0.1 1000 -06 -07 2 55 FN9260vB-6-yy-zz 6 (6.9) 0.00 0.3 0.1 1000 -06 -07 2 55 FN9260vB-10-yy-zz 10 (11.5) 0.00 0.2 0.1 1000 -06 -07 2 55 FN261v-1-06-zz 1 (1.2) 0.31 (0.18) 5.3 0.1 2.2 1000 -06 1 55 FN261v-2-06-zz 2 (2.3) 0.31 (0.18) 2.7 0.1 2.2 1000 -06 1 55 FN261v-4-06-zz 4 (4.6) 0.31 (0.18) 1.0 0.1 2.2 1000 -06 1 55 FN261v-6-06-zz 6 (6.9) 0.31 (0.18) 0.3 0.1 2.2 1000 -06 1 55 FN261v-10-06-zz 10 (11.5) 0.31 (0.18) 0.2 0.1 2.2 1000 -06 1 55 * Leakage current under normal operating conditions (acc. to IEC60939-3). Note: if the neutral line is interrupted, worst case leakage could reach twice this level. ** Tolerances apply: Inductance: -30/+50%, Capacitance: 20%, Resistance: 10% *** Fuses are not included in the filter and need to be selected according to application Product selector FN9260vw-xx-yy-zz Snap-in range for S version only 10: Snap-in range0.6 to 1.5mm 20: Snap-in range 1.6 to 2.5mm 30: Snap-in range 2.6 to 3.5mm 06: Fast-on 6.3 x 0.8mm (spade/soldering) 07: Wire leads 1 to 10: Rated current Blank: Standard version A: Safety version B: Medical version (without Y-capacitor) Blank: Standard housing with mounting flanges S: Snap-in version,snapperon verticalside For example: FN9260-1-06-10, FN9260SB-10-06-20, FN261S-6-06-30