Product data sheet ATV12H075M3 Characteristics variable speed drive ATV12 - 0.75kW - 1hp - 200..240V - 3ph - with heat sink Product availability: Stock - Normally stocked in distribution facility Main Range of product Altivar 12 Product or component Variable speed drive type Product destination Asynchronous motors Product specific applica- Simple machine tion Assembly style With heat sink Component name ATV12 Quantity per set Set of 1 EMC filter Without EMC filter Built-in fan Without Phase 3 phases Us rated supply volt- 200...240 V - 15...10 % age Motor power kW 0.75 kW Motor power hp 1 hp Communication port Modbus protocol Line current 6.3 A 200 V 5.3 A 240 V Speed range 1...20 Transient overtorque 150...170 % of nominal motor torque depending on drive rating and type of motor Asynchronous motor Quadratic voltage/frequency ratio control profile Voltage/Frequency ratio (V/f) Sensorless flux vector control IP degree of protection IP20 without blanking plate on upper part Noise level 0 dB Complementary Supply frequency 50/60 Hz +/- 5 % Connector type 1 RJ45 Modbus on front face Physical interface 2-wire RS 485 Modbus Transmission frame RTU Modbus Transmission rate 4800 bit/s 9600 bit/s 19200 bit/s 38400 bit/s Number of addresses 1...247 Modbus Communication service Read holding registers (03) 29 words Write single register (06) 29 words Write multiple registers (16) 27 words Read/Write multiple registers (23) 4/4 words Read device identification (43) Prospective line Isc <= 5 kA Continuous output current 4.2 A 4 kHz Maximum transient current 6.3 A 60 s Speed drive output frequency 0.5...400 Hz Nominal switching frequency 4 kHz Aug 9, 2019 1 The information provided in this documentation contains general descriptions and/or technical characteristics of the performance of the products contained herein. This documentation is not intended as a substitute for and is not to be used for determining suitability or reliability of these products for specific user applications. It is the duty of any such user or integrator to perform the appropriate and complete risk analysis, evaluation and testing of the products with respect to the relevant specific application or use thereof. Neither Schneider Electric Industries SAS nor any of its affiliates or subsidiaries shall be responsible or liable for misuse of the information contained herein.Switching frequency 2...16 kHz adjustable 4...16 kHz with derating factor Braking torque Up to 70 % of nominal motor torque without braking resistor Motor slip compensation Adjustable Preset in factory Output voltage 200...240 V 3 phases Electrical connection Terminal 3.5 mm AWG 12 L1, L2, L3, U, V, W, PA, PC Tightening torque 7.08 lbf.in (0.8 N.m) Insulation Electrical between power and control Supply Internal supply for reference potentiometer 5 V DC 4.75...5.25 V 10 mA overload and short-circuit protection Internal supply for logic inputs 24 V DC 20.4...28.8 V 100 mA overload and short- circuit protection Analogue input number 1 Analogue input type Configurable voltage AI1 0...10 V 30 kOhm Configurable voltage AI1 0...5 V 30 kOhm Configurable current AI1 0...20 mA 250 Ohm Discrete input number 4 Discrete input type Programmable LI1...LI4 24 V 18...30 V Discrete input logic Negative logic (sink) > 16 V < 10 V 3.5 kOhm Positive logic (source) 0...< 5 V > 11 V Sampling duration 20 ms +/- 1 ms logic input 10 ms analogue input Linearity error +/- 0.3 % of maximum value analogue input Analogue output number 1 Analogue output type Software-configurable voltage AO1 0...10 V 470 Ohm 8 bits Software-configurable current AO1 0...20 mA 800 Ohm 8 bits Discrete output number 2 Discrete output type Logic output LO+, LO- Protected relay output R1A, R1B, R1C 1 C/O Minimum switching current 5 mA 24 V DC logic relay Maximum switching current 2 A 250 V AC inductive cos phi = 0.4 L/R = 7 ms logic relay 2 A 30 V DC inductive cos phi = 0.4 L/R = 7 ms logic relay 3 A 250 V AC resistive cos phi = 1 L/R = 0 ms logic relay 4 A 30 V DC resistive cos phi = 1 L/R = 0 ms logic relay Acceleration and deceleration ramps U Linear from 0 to 999.9 s S Braking to standstill By DC injection <= 30 s Protection type Against input phase loss in three-phase Thermal motor protection via the drive by continuous calculation of It Line supply overvoltage Line supply undervoltage Overcurrent between output phases and earth Overheating protection Short-circuit between motor phases Frequency resolution 0.1 Hz display unit Converter A/D, 10 bits analog input Time constant 20 ms +/- 1 ms for reference change Marking CE Operating position Vertical +/- 10 degree Height 5.63 in (143 mm) Width 2.83 in (72 mm) Depth 5.17 in (131.2 mm) Product weight 1.76 lb(US) (0.8 kg) Specific application Commercial equipment Variable speed drive application selection Commercial equipment : mixer Commercial equipment : other application Textile : ironing Motor starter type Variable speed drive 2