FS15A Sensata

FS Series Flow Switches Flow detection switches 15mm and 22mm tube versions Low flow versions available Maximum Operating Pressure 10 bar WRAS approved for use in cold and hot water up to 60C Operating temperature rated to 85C Technical Specification Material Acetal Resin Colour Black Temp. Range C -20 / +85 F -4 ./ +185 FS15A FS15LF FS22A FS22LF Must operate flow rate* litres/min 2.0 0.90 3.75 1.75 US Gal/min 0.53 0.24 0.99 0.47 Must release flow rate litres/min 0.3 0.25 1.40 0.75 US Gal/min 0.08 0.07 0.37 0.20 Cable 25cm PVC insulated Electrical Specification Contact Form N/O with no flow Switching Power Max VA 25 Switching Voltage AC Max V 240 Switching Voltage DC Max V 120 These flow switches are designed for use Switching Current Max A 0.6 in liquid flow systems at pressures up to All ratings are for resistive load only. 10 bar and temperatures up to 85C. Standard Parts Must operate l/min Must release l/min Approvals FS15A 2.0 0.3 WRAS The design is based around a moving FS15LF 0.90 0.25 WRAS magnet and a fixed reed switch with a low FS22A 3.75 1.40 WRAS flow restriction. FS22LF 1.75 0.75 WRAS * The switch will have operated (contacts close) when the flow rate rises above this value. The switch will have released (contacts open) when the flow rate falls below this value. The switches are designed to be used in liquids only and should not be used in NB Operate and release flow rates only apply when the switch is mounted with the flow direction vertical. The systems with significant amounts of solid sensitivity of the switch is reduced when mounted with the flow direction horizontal. particles. Installation Flow switches can be mounted with the flow direction horizontal or vertical (upward flow). The cap with cable Custom versions can be made for particular applications. connection must always be upwards, as the piston is returned to its released position by gravity. When using metal compression fittings to connect flow switches to copper tube, care must be taken not to over-tighten the fittings onto the flow switch body. CAUTION The use of plastic plumbing fittings may affect the electrical earth continuity bonding as required by IEE regulations. If in doubt, consult a qualified electrician. Mechanical Dimensions FS15 FS22 0ART.UMBERING3YSTEM 15mm (0.59 ) 22mm (0.87 ) 114mm 107mm Cynergy3 Components Ltd. (4.21) (4.48 ) 7 Cobham Road Ferndown Industrial Estate Wimborne, Dorset BH21 7PE, UK 56mm 58mm Telephone: +44 (0)1202 897969 Email: c3w sales sensata.com (2.28 ) (2.20 ) All dimensions are in millimeters (inches) ISO9001C E R T I F I ED Made in the UK www.cynergy3.com cynergy3-fs-v2 2020 Cynergy3 Components, All Rights Reserved. Specifications are subject to change without prior notice. Cynergy3 Components and the Cynergy3 Components logo are trademarks of Cynergy3 Components Limited.X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Environmental Test Equipment category: Click to view products by Sensata manufacturer: Other Similar products are found below : CW40 F150C10E3DRT F150LTC20 F150CD10E2 F150L75 F150LRS 2837806 4328074 4366444 S-11 382153 700PTP-1 GEO- CABLE-REEL-50M H115 H300 F150-SLC50 AW-CO-1000 AW-H2S-100 AW-NmHc-100 ES1-CO-1000-01 P 2801 P 2802 TM-197 ULD-420-EUR TM-192 TM-192D TM-305U TM-414 UT309C EL-P-TC-T-SURFACE UT301C+ HS115 12227021 13123602 13123661 12255930 12983030 30171091 30198712 30198755 30209323 12228657 12229067 12230090 7358958 12231398 12231487 7390682 12231550 7391840