H16WD6075G-10 Sensata

Panel Mount Datasheet H16WD Series Ratings from 25A to 90A @ 48-690 VAC DC control 1600 Volts Blocking Direct Bond Copper substrate SCR output for heavy industrial loads EMC Compliant to Level 3 Zero voltage or instantaneous turn-on outputs Direct Power Lead Frame UL/CSA/VDE Approved, CE Compliant to EN60950-1 Epoxy Free Design Improved SEMS screw and washer Redesigned housing with anti-rotation barriers For Generation 3 datasheet click here PRODUCT SELECTION Control Voltage 25A 50A 75A 90A 4-32 Vdc H16WD6025 H16WD6050 H16WD6075 H16WD6090 AVAILABLE OPTIONS Rated Load Current 25: 25 Amps 50: 50 Amps Input Status LED Switching Type Transient Overvoltage 75: 75 Amps Blank: Not Included Blank: Zero Voltage Turn-On Series 6WD: 1600 Vpk 90: 90 Amps G: Included -10: Instantaneous Turn-On (3) H1 6WD 60 25 K G H -10 Operating Voltage Termination Thermal Pad 60: 48-690 VAC Blank: Screw Blank: Not Included F: Quick Connect (1) H: Included Required for valid part number (Up to 50 Amps models) For options only and not required for valid part number (2) K: Hex standoffs * Not all part number combinations are available. Contact Crydom Technical Support for informacion on the availability of a specific part number. (4) OUTPUT SPECIFICATIONS Description 25A 50A 75A 90A Operating Voltage (47-440Hz) [Vrms] 48-690 48-690 48-690 48-690 Transient Overvoltage [Vpk] 1600 1600 1600 1600 Rated Load Current [Arms] (5)(2) 25 50 75 90 Rated Load Current {UL508 Motor Controller} [Arms] (5) 10 20 30 45 Minimum Load Current [mArms] 150 150 150 150 Maximum Off-State Leakage Current @ Rated Voltage [mArms] 1.0 1.0 1.0 1.0 Minimum Off-State dv/dt @ Maximum Rated Voltage [V/sec] 500 500 500 500 Maximum 1 Cycle Surge Current (50/60Hz) [Apk] 239/250 597/625 954/1000 1145/1200 Maximum It for Fusing (50/60Hz) [A sec] 285/259 1779/1621 4555/4150 6560/5976 Thermal Resistance Junction to Case (Rjc) [C/W] 0.8 0.45 0.3 0.27 Maximum On-State Voltage Drop @ Rated Current [Vrms] 1.3 1.3 1.2 1.2 HP rating UL 508/IEC60947[HP (KW)]: 240 VAC 1.5 (1.1) 3 (2.2) 5 (3.7) 7.5 (5.6) HP rating UL 508/IEC60947[HP (KW)]: 380 VAC 2 (1.5) 5 (3.7) 7.5 (5.6) 15 (11.2) HP rating UL 508/IEC60947[HP (KW)]: 480 VAC 3 (2.2) 5 (3.7) 10 (7.4) 20 (14.9) HP rating UL 508/IEC60947[HP (KW)]: 600 VAC 3 (2.2) 10 (7.4) 15 (11.2) 25 (18.6) Minimum Power Factor (at Maximum Load) 0.5 0.5 0.5 0.5 Do not forget to visit us at: www.crydom.com Copyright 2016 Crydom Inc. Specifications subject to change without notice.Panel Mount Datasheet (4) INPUT SPECIFICATIONS Description DC Control Control Voltage Range 4-32 VDC Minimum Turn-On Voltage (6) 4.0 VDC Must Turn-Off Voltage 1.0 VDC Maximum Reverse Voltage -32 VDC Minimum Input Current @ Minimum Voltage (for on-state) 7mA Maximum Input Current @ Maximum Voltage 12mA Nominal Input Impedance Current Regulated Maximum Turn-On Time [msec] (7) 1/2 Cycle Maximum Turn-Off Time [msec] 1/2 Cycle (4) GENERAL SPECIFICATIONS Description Parameters Dielectric Strength, Input/Output/Base (50/60Hz) 4000 Vrms 9 Minimum Insulation Resistance (@ 500 VDC) 10 Ohm Maximum Capacitance, Input/Output 8 pF Ambient Operating Temperature Range -30 to 80 C Ambient Storage Temperature Range -40 to 125 C Weight (typical) 2.6 oz (74.9 g) Housing Material UL 94 V-0 SSR Mounting Torque Range [in lbs/Nm] 18-20 (2-2.2) Baseplate Material Aluminum Input Terminal Screw Torque Range [in-lb/Nm] 13-15 /1.5-1.7 Output Terminal Screw Torque Range [in lb/Nm] 18-20 (2-2.2) SSR Mounting Screw Torque Range [in-lb/Nm] 18-20 / 2.0-2.2 Input/Load Terminal Screw Torque Range [in-lb/Nm] (2) w/K option 8-10 / 0.9-1.13 Input/Output Terminal Screw Thread Size #6-32 UNC / #8-32 UNC Humidity per IEC60068-2-78 93% non-condensing LED Input Status Indicator w/G option (green) 11,641,553 hours (1,328 years) MTBF (Mean Time Between Failures) at 40C ambient temperature (8) 7,210,376 hours (823 years) MTBF (Mean Time Between Failures) at 60C ambient temperature (8) WIRING DIAGRAM AC Input Current vs Input Voltage Recommended Wire Sizes V Standard Regulated DC Input Wire Size Wire Pull-Out 25 Terminals (Solid / Stranded) Strength (lb)[N] Load (9) 20 2 24 AWG (0.2 mm ) / 0.2 [minimum] 10 [44.5] Input 1 ( ) 2 ( ) 2 15 2 x 12 AWG (3.3 mm ) / 3.3 [maximum] 90 [400] 2 10 20 AWG (0.5 mm ) / 0.518 [minimum] 30 [133] Output 2 2 2 x 10 AWG (5.3 mm ) / 5.3 1 OUTPUT 110 [490] 5 S OL I D S T A T E R EL A Y 2 2 x 8 AWG (8.4 mm ) / 8.4 [maximum] 90 [400] 0 0 5 10 15 20 25 30 4 INPUT 3 DC Input Voltage 4 () 3 (+) EQUIVALENT CIRCUIT BLOCK DIAGRAM 4 1 -DC AC (10) Trigger Circuit +DC 3 2 AC Current Limiter Do not forget to visit us at: www.crydom.com Copyright 2016 Crydom Inc. Specifications subject to change without notice. Input Current (mA)