OLS5 Series Optical liquid level sensor - Internal M10 mount Low cost sensors for general liquid sensing High reliability optical sensing Internal mount via M10x1 thread Standard temperature range -25C to +80C Extended temperature range -40C to +125C High and Low output versions Resistant to false triggering caused by foaming Technical Specification Mounting style Internal Cable length - standard 25cm Mounting thread M10x1 Wire size 24AWG Body material Polysulfone UDEL 1700 Cable conductor material Tinned copper Temperature Range -25 to +80C/-40 to +125C Wire sheath material PTFE Maximum pressure 20 bar Wire temperature rating 125C The OLS5 series is a liquid level sensor for Tightening torque for fixing1.5Nm/13.26lbs in Sealing gasket & nut Not supplied single point liquid level detection. Electrical Specification Supply Voltage (Vs) Vdc 4.5 to 15.4 The sensor has an infra-red emitter and Supply Current Max (Is) mA 2.5 (Vs = 15.4Vdc) detector aligned within an accurately Output type Voltage High or Low shaped cone to give good optical coupling Output Voltage (Vout) Iout=100mA Output High Vout = Vs-1V max Output Low Vout = 0.5Vmax when the sensor is in air. This coupling is Output Sink & Source Current Iout 100mA max greatly reduced, when the sensor is immersed in liquid, as the infra-red light escapes through the liquid rather than being reflected back to the detector. Sensor connections Red= supply +ve, Blue= common(0V), Green= Output (see diagrams overleaf) The sensor has a transistor output, so can be configured by the user for particular Standard Parts Mount Temp Range C Supply Volts V Output applications. OLS500D3 M10x1 -25 to +80 5 to 15dc High in air OLS500D3L M10x1 -25 to +80 5 to 15dc Low in air Output is via TTL compatible push pull OLS510D3 M10x1 -40 to +125 5 to 15dc High in air output. OLS510D3L M10x1 -40 to +125 5 to 15dc Low in air Custom versions can be made for particular applications. Please contact Cynergy3 with your requirements. Mechanical Dimensions M10x1 ThreadM10x1 Thread 12 1010 22.7022.70 Cynergy3 Components Ltd. 7 Cobham Road, Ferndown Industrial Estate, Wimborne, Dorset, BH21 7PE, United Kingdom Telephone: +44 (0)1202 897969 Email: c3w sales sensata.com ISO9001C E R T I F I ED Made in the UK www.cynergy3.com cynergy3-ols5-v2 2020 Cynergy3 Components, All Rights Reserved. Specifications are subject to change without prior notice. Cynergy3 Components and the Cynergy3 Components logo are trademarks of Cynergy3 Components Limited.OLS5 Series Optical liquid level sensor - Internal M10 mount Installation The sensor can be mounted in either the side or the bottom of a tank. It Installation with back nut must not be mounted in the top of a tank with the cone downwards. Fixing nut M10x1* O ring gasket* This sensor requires a hole of 10mm minimum or an M10x1 thread socket Red wire =+Vs connection. The hole should be in a flat surface and be free of burrs. Green wire =Output Blue wire = 0V The sensor with suitable gasket should be inserted into the hole and a fixing nut fitted on the M10 thread on the outside of the tank. Alternatively the sensor can be screwed into a M10x1 socket. The sensor should not be *Note. M10 nut and O ring not supplied overtightened. Cleaning Installation in M10x1 socket Proper fluids should be selected based on the type of contamination to be removed. It is recommended that freon or alcohol based solvents are used. M10x1 socket DO NOT USE chlorinated solvents such as trichloroethylene as these are likely to attack the sensor housing material. Liquid Media Compatibility Check that the fluid in which you wish to use the sensor is compatible with Polysulfone. Electrical Connections www.cynergy3.com ISO9001C ER TI FI ED 2020 Cynergy3 Components, All Rights Reserved. Specifications are subject to change without prior notice. Cynergy3 Components and the Cynergy3 Components logo are trademarks of Cynergy3 Components Limited.