PMP2425WP Sensata

Control Relays Datasheet PMP Series Proportional Control SSRs Single Phase Proportional Controller Output ratings up to 90 Amps at 600 VAC Selectable operation mode: Phase Angle or Burst Fire control Selectable Control Input: 0-5 VDC, 0-10 VDC, 4-20 mA 50/60 Hz Adaptive Operational Frequency function 4-20 mA input does not require an auxiliary power supply LED multifunction status indicator Contactor configuration withElevato screw terminals cURus, IEC Rated, CE & RoHS Compliant The PMP Series of micro-controller based Single-Phase method to be used can be selected on the unit by means of a Proportional Control SSRs are designed to offer precise control of selector switch located on top of the SSR. the power delivered to a resistive load in a compact 22.5mm This selector switch also allows to select the type of analog signal housing, with ratings from 25 up to 90 Amps at 90 to 600 VAC. to be used at the control input. The available input types are: 0- 5 PMP Series solid state relays can vary the output load power VDC, 0-10 VDC, and 4-20 mA. proportionally to an analog control input from 0 to 100%. This can PMP Series Proportional SSRs are ideal for lamp dimming and be achieved by two different methods: Phase Angle control and resistive heating control, among other type of applications Burst Fire control (with Distributive Zero Cross). The control requiring proportional control. PRODUCT SELECTION Output Voltage 25 A 50 A 90 A 90-280 VAC PMP2425W PMP2450W PMP2490W 345-530 VAC PMP4825W PMP4850W PMP4890W 420-600 VAC PMP6025W PMP6050W PMP6090W AVAILABLE OPTIONS Operating Voltage 24: 90-280 VAC Terminal Layout Thermal Pad 48: 345-530 VAC W: Contactor Configuration Blank: Not Included Series 60: 420-600 VAC (elevator screw) H: Included PMP 24 25 W P H Rated Load Current Overvoltage Protection (1) 25: 25 Amps Blank: Not Included Required for valid part number 50: 50 Amps P: Included For options only and not required for valid part number 90: 90 Amps (2) OUTPUT VOLTAGE SPECIFICATIONS Description PMP24xxW PMP48xxW PMP60xxW Operating Voltage (45-65Hz) VRMS 90-280 345-530 420-600 Transient Overvoltage Vpk (1) 600 1200 1200 Maximum Off-State Leakage Current Rated Voltage mARMS 4 2.2 2 Minimum Off-State dV/dt Maximum Rated Voltage V/sec 500 500 500 FDE-07-01 REV. A Do not forget to visit us at: www.crydom.com Copyright 2017 Crydom Inc. Specifications subject to change without notice.Control Relays Datasheet (2) OUTPUT SPECIFICATIONS Description 25 A 50 A 90 A Load Current, General Use UL508 40C ARMS (3) 25 50 90 Minimum Load Current mARMS (4) 100 100 150 Maximum 1 Cycle Surge Current (50/60Hz) Apk 286/300 716/750 1290/1350 Maximum On-State Voltage Drop Rated Current Vrms 1.15 1.15 1.2 Maximum 1/2 Cycle I t for Fusing (50/60Hz) A sec 409/375 2563/2343 8320/7593 Thermal Resistance Junction to Case (Rjc) C/W 0.49 0.27 0.2 Maximum Power Dissipation Rated Current W 29 58 104 Recommended Heat Sink for Rated Current 40C C/W 2 1 0.36 Minimum Power Factor (at Maximum load) 0.7 0.7 0.7 Phase Angle Control Range % 0 to 100 0 to 100 0 to 100 Burst Fire Distributive Control Time Base Period 0 to 20 Cycles 0 to 20 Cycles 0 to 20 Cycles (2)(5)(6) POWER SUPPLY SPECIFICATIONS Description PMP Supply Voltage Range VDC 8-30 Maximum Supply Current mA 30 Overvoltage Protection Limited to 35 VDC for 60 sec Reverse Polarity Protection Yes (2) INPUT SPECIFICATIONS Description Voltage Control Current Control Valid Input Voltage VDC / Current mA 0-10, 0-5 4-20 Maximum Allowed Input Voltage VDC / Current mA 30 35 Maximum Reverse Voltage VDC /Current mA -30 -35 Pick up Voltage VDC / Current mA 0.4 4.3 Dropout Voltage VDC / Current mA 0.1 4 Nominal Input Impedance Ohms 28.8k 230 20 mA Maximum Initialization Time msec 5 Cycles 5 Cycles Response Time 1 Cycle 1 Cycle (2) GENERAL SPECIFICATIONS Description Parameters Dielectric Strength, Input to Output (50/60Hz) 4000 VRMS Dielectric Strength, Input/Output to Baseplate (50/60Hz) 4000 VRMS 9 Minimum Insulation Resistance ( 500 VDC) 10 Ohms Maximum Capacitance, Input/Output 8 pF Ambient Operating Temperature Range (7) -25 to 70 C Ambient Storage Temperature Range (7) -25 to 70 C Weight (typical) 2.6 oz (73 g) Housing Material UL94 V-0 Aluminum Baseplate Material Hardware Finish Nickel Plating SSR Mounting Screw Torque Range (in-lb/Nm) 20-25/2.2-2.8 93% non-condensing Humidity per IEC 60068-2-78 LED Input Status Indicator See Status Chart Overvoltage Category III Impulse Withstand Voltage According to IEC 60664-1 6 kV Adaptative Operational Frequency Function Yes Do not forget to visit us at: www.crydom.com Copyright 2017 Crydom Inc. Specifications subject to change without notice.