SMR2450-6 Sensata

Panel Mount DataSheet SMR24 -6 Series System monitoring solid-state relay Ratings from 25A to 90A 60-280 VAC DC control LED status indicators Alarm output signal Inverting or non-inverting input Normally open or normally closed alarm output PRODUCT SELECTION Control Voltage 25 A 50 A 90 A 8-32 VDC SMR2425-6 SMR2450-6 SMR2490-6 AVAILABLE OPTIONS Output Current 25: 25 Amps 50: 50 Amps Series 90: 90 Amps SMR 24 25 -6 Output Voltage Features 24: 60-280 VDC Input: Inverting or Non Inverting Alarm Output: Normally Open or Normally Closed Required for valid part number For options only and not required for valid part number (1) OUTPUT SPECIFICATIONS Description SMR2425-6 SMR2450-6 SMR2490-6 Operating Voltage (47-63Hz) Vrms 60-280 60-280 60-280 Transient Overvoltage Vpk 600 600 600 Maximum Off-State Leakage Current Rated Voltage mArms 10 10 10 Minimum Off-State dv/dt Maximum Rated Voltage V/sec (2) 500 500 500 25 50 90 Maximum Load Current Arms (3) 40 40 40 Minimum Load Current Arms Maximum 1 Cycle Surge Current (50/60Hz) Apk 239/250 597/625 1145/1200 Maximum On-State Voltage Drop Rated Current Vpk 1.6 1.6 1.6 Thermal Resistance Junction to Case (Rjc) C/W 1.02 0.63 0.28 285/259 1779/1621 6560/5976 Maximum 1/2 Cycle It for Fusing (50/60 Hz) A sec Minimum Power Factor (with Maximum Load) 0.5 0.5 0.5 (1)(4) CONTROL SPECIFICATIONS Description INVERTING NON-INVERTING Logic Supply Voltage Range 8-32 VDC (pin 3) 8-32 VDC (pin 3) Logic Supply Current 12 8 mA 14 mA (plus pin 8 loading) Input-On Voltage Range 8-32 VDC (pin 6) 0-1.0 VDC (pin 5) 0-0.4 VDC (pin 6) 8-32 VDC (pin 5) Input-Off Voltage Range 6 mA 1.0 mA Input-On Current 12 VDC Logic Supply Maximum Turn-On Time msec 1/2 Cycle 1/2 Cycle Maximum Turn-Off Time msec 1/2 Cycle 1/2 Cycle Do not forget to visit us at: www.crydom.com Copyright 2017 Crydom Inc. Specifications subject to change without notice.Panel Mount DataSheet (1)(4) ALARM SPECIFICATIONS Description NORMALLY OPEN NORMALLY CLOSED Alarm-On VoltageSupply Voltage (with load) Open Col. NPN (pin 7Supply Voltage (minus 1.0 V) Active High PNP (pin 8 Alarm-Off Voltage0.0 VDC (with load) Open Col. PNP (pin 81.5 VDC Active Low NPN (pin 7 Maximum Alarm Output Current 100 mA 100 mA Alarm Delay (Min.-Max.) 30-100 msec 30-100 msec GENERAL SPECIFICATIONS Description Parameters Dielectric Strength, Input/Output (50/60Hz) 4000 Vrms 9 Minimum Insulation Resistance ( 500 V DC) 10 Ohms Maximum Capacitance, Input/Output 8 pF Ambient Operating Temperature Range -40C to 80C Ambient Storage Temperature Range -40C to 125C Weight (typical) 3.0 oz (86.5g) Encapsulation Thermally Conductive Epoxy Ambient Operating Temperature Range Screws and Saddle Clamps Furnished, Unmounted Ambient Storage Temperature Range ITW Pancon No. MTSS100-6 or Equivalent Weight (typical) ITW Pancon No. CT100F22-6 or Equivalent Encapsulation 8-32 & 10-32 Screws - 20 in. lbs. (Screws dry without grease) GENERAL NOTES (1) All parameters at 25C unless otherwise specied. (2) Off-State dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1 (3) Heat sinking required, for derating curves see page 2. (4) All voltages are positive in respect to common (pin 4) WIRING DIAGRAM AC AC 2 1 Logic Supply 8-32 Vdc Red LED Common (-) Alarm Status 3 Control Non-Inverting Control Inverting Green LED Input Status Alarm N/C 8 Alarm N/0 STATUS CHART Load Normal Normal Line Logic Relay Line Voltage Logic Relay Relay Circuit Relay Relay Voltage Supply Fails Low Supply Loss Fails to Fails High OFF ON Low Loss Shorted w/Control w/Control Turn ON Shorted Impedance LINE VOLTAGE LOAD CURRENT CONTROL INVERTING CONTROL NON-INVERTING GREEN LED LOGIC SUPPLY RED LED & ALARM N/O ALARM N/C Do not forget to visit us at: www.crydom.com Copyright 2017 Crydom Inc. Specifications subject to change without notice.