REGIN Si5xx/514/570-PROG-EVB 2 Si514/570/571/598/599 ANY-FREQUENCY I C P ROGRAMMABLE XO/VCXO EVALUATION BOARD Description Features The Skyworks Si514/570/571/598/599 evaluation kit Evaluation of Skyworks Si514/570/571/598/599 2 contains the hardware and software needed for Any-Frequency I C programmable XO/VCXO evaluation of the Si514/570/571/598/599 Any- Windows-compatible software control and device 2 Frequency I C programmable XO/VCXO and can be programming run on a USB-equipped PC. Voltage regulator supports device operation of the Si5xx at +1.8, +2.5, or +3.3 V 2 I C communication options are jumper configurable Voltage control (VC) input port (Si571/Si599) Functional Block Diagram TP1 TP2 (EXT3P3V) (VBUS 5V) J1 J2 Optional USB Power In TP10 VCO In 1 2 Filter TP3 3 (VDD DUT) TP6 TP7 (SCL) (SDA) J12 C8051F342 VDD MCU REG J5 4 3 J20 2 1 Manual VDD Voltage Select 4-3=2.5V 12 3 J11 2-1=3.3V OPEN=1.8V J17 2 TP4 1 J13 3 2 8 DUT 1 1 6 SDA (VC) VDD Level J14 Translator 2 5 1 SCL (OE) CLKP CLKP J16 Output 2 Conditioner J18 Level 3 4 3 GND CLKN CLKN Translator 7 J19 Output Enable 2 1 Skyworks Solutions, Inc. Phone 781 376-3000 Fax 781 376-3100 sales skyworksinc.com www.skyworksinc.com Rev. 0.3 Skyworks Proprietary Information Products and Product Information are Subject to Change Without Notice October 12, 2021 NC (SDA) NC (SCL)1. Introduction This document describes the operation of the Skyworks Si514/570/571/598/599 evaluation kit. The Si5xx-PROG- EVB kit refers to the evaluation board hardware and software intended for customer evaluation of the 2 Si514/570/571/598/599 Any-Frequency I C programmable XO/VCXO. The Si5xx-EVB kit contains the following: Si5xx-PROG-EVB Hardware Programmable Oscillator Software EVB Driver (USBXpress ) The software components run on a USB-equipped PC and are described in detail in Section 5. Software Guide 2 The Si5xx-PROG-EVB evaluation board can be used to evaluate the Si514, Si570, Si571, Si598, and Si599 I C programmable XOs or VCXOs as shown in Table 1. The Si514-PROG-EVB evaluation board can be used to 2 evaluate the Si514 I C-programmable XO as shown in Table 1. This evaluation board functions and performs similar to the Si5xx-PROG-EVB evaluation board. Table 1. Si5xx XO and VCXO Device Evaluation Board Selector Guide Ordering Part Type Devices Packages Output Format, Supported Supported Supported Temp Stability, Frequency Tuning Slope Range Si5xx-EVB Single/Dual Frequency Si510/511 5 x 7 mm, 6-pin Any 100 kHz to XO/VCXO Eval Board Si512/513 3.2 x 5 mm, 6-pin 1417 MHz Si515/516 3.2 x 5 mm, 4-pin Si530/531 Si532/533 Si550/552 Si590/591 2 Si5xx-PROG-EVB I C Programmable Si514 5 x 7 mm, 8-pin Any 100 kHz to XO/VCXO Eval Board Si570/571 5 x 7 mm 6-pin 1417 MHz Si598/599 3.2 x 5 mm, 6-pin 2 Si514-PROG-EVB I C Programmable XO Si514 5 x 7 mm 6-pin Any 100 kHz to Eval Board with sol- 250 MHz dered Si514 Si5xx5x7-EVB Quad Frequency Si534 5 x 7 mm, 8-pin Any 10 to XO/VCXO Eval Board Si554 1417 MHz 2 Si570-PROG-EVB I C Programmable XO Si570 5x7 mm 8-pin Any 10 to Eval Board with sol- 1417 MHz dered Si570 Notes: 1. Si5xx samples must be ordered separately from the Si5xx-PROG-EVB. 2. Board must be modified to be consistent with the ordered part. See3.10. Output Termination on page 8. 3. Si514-PROG-EVB comes with an Si514 preinstalled. 2 Skyworks Solutions, Inc. Phone 781 376-3000 Fax 781 376-3100 sales skyworksinc.com www.skyworksinc.com Rev. 0.3 Skyworks Proprietary Information Products and Product Information are Subject to Change Without Notice October 12, 2021