SLWRB4167A Silicon Labs

UG283: EFR32MG13 2400/868 MHz 10 dBm Wireless Starter Kit User s Guide A Wireless Starter Kit with the BRD4167A Radio Board is an ex- BRD4167A RADIO BOARD FEATURES cellent starting point to get familiar with the EFR32 Mighty Gecko Wireless System-on-Chip. It also provides all necessary EFR32MG13 Mighty Gecko Wireless SoC with 512 kB Flash, and 64 kB RAM tools for developing a Silicon Labs wireless application. (EFR32MG13P733F512GM48) Dual band integrated radio transceiver BRD4167A is a plug-in board for the Wireless Starter Kit Mainboard. It is a complete ref- erence design for the EFR32MG13 Wireless SoC, with matching networks for 10 dBm 10 dBm output power output power, a 2.4 GHz PCB antenna, and an SMA connector for the 868 MHz band. Inverted-F PCB antenna (2.4 GHz) SMA antenna connector (868 MHz) The Wireless Starter Kit Mainboard contains an on-board J-Link debugger with a Packet 8 Mbit low-power serial flash for over-the- Trace Interface and a virtual COM port, enabling application development and debugging air upgrades. of the attached radio board as well as external hardware. The mainboard also contains sensors and peripherals for easy demonstration of some of the EFR32 s many capabili- WIRELESS STK MAINBOARD FEATURES ties. Advanced Energy Monitor This document describes how to use the BRD4167A Radio Board together with a Wire- Packet Trace Interface less Starter Kit Mainboard. Virtual COM port SEGGER J-Link on-board debugger External device debugging Ethernet and USB connectivity Silicon Labs Si7021 relative humidity and temperature sensor Low power 128x128 pixel Memory LCD- TFT User LEDs / pushbuttons 20-pin 2.54 mm EXP header Breakout pads for Wireless SoC I/O CR2032 coin cell battery support SOFTWARE SUPPORT Simplicity Studio Energy Profiler Network Analyzer ORDERING INFORMATION SLWRB4167A silabs.com Building a more connected world. Rev. 1.01 Table of Contents 1. Introduction................................4 1.1 Radio Boards..............................4 1.2 Ordering Information ...........................4 1.3 Getting Started .............................4 2. Hardware Overview.............................5 2.1 Hardware Layout.............................5 2.2 Block Diagram..............................6 3. Connectors................................7 3.1 J-Link USB Connector...........................7 3.2 Ethernet Connector............................7 3.3 Breakout Pads .............................8 3.4 EXP Header ..............................9 3.4.1 EXP Header Pinout..........................10 3.5 Debug Connector.............................11 3.6 Simplicity Connector............................12 3.7 Debug Adapter .............................13 4. Power Supply and Reset.......................... 14 4.1 Radio Board Power Selection ........................14 4.2 Board Controller Power...........................15 4.3 EFR32 Reset..............................15 5. Peripherals............................... 16 5.1 Push Buttons and LEDs ..........................16 5.2 Memory LCD-TFT Display..........................17 5.3 Serial Flash ..............................18 5.4 Si7021 Relative Humidity and Temperature Sensor .................19 5.5 Virtual COM Port.............................20 5.5.1 Host Interfaces ...........................21 5.5.2 Serial Configuration..........................21 5.5.3 Hardware Handshake .........................22 6. Board Controller............................. 23 6.1 Admin Console .............................23 6.1.1 Connecting.............................23 6.1.2 Built-in Help ............................23 6.1.3 Command Examples .........................24 6.2 Virtual UART ..............................24 7. Advanced Energy Monitor ......................... 25 silabs.com Building a more connected world. Rev. 1.01 2