DATA SHEET SE2600S: 2.4 GHz WLAN Switch/Low-Noise Amplifier Front-End Applications IEEE802.11b DSSS WLAN IEEE802.11g/n OFDM WLAN Embedded systems Features Integrates an SP3T switch and LNA with bypass mode Gain: 12 dB Noise Figure: 1.8 dB Bluetooth path loss: 0.5 dB Small WLCSP (11-bump, 1.07 x 1.05 x 0.38 mm) 250 m ball pitch package (MSL1, 260 C per JEDEC-J-STD-020) Figure 1. SE2600S Block Diagram Description The SE2600S is an integrated Front-End Module (FEM) with a Bluetooth port to complement WLAN chipsets with an integrated Power Amplifier (PA). The SE2600S integrates a Single-Pole, Triple-Throw (SP3T) switch and Low-Noise Amplifier (LNA) with a bypass mode in an ultra- compact package. The device is capable of switching between WLAN receive, WLAN transmit, and Bluetooth. The SE2600S is provided in a small, 11-bump, 1.07 x 1.05 mm Wafer Level Chip Scale Package (WLCSP). A functional block diagram is shown in Figure 1. The pin configuration and package are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. Figure 2. SE2600S Pinout 11-Bump CSP (Top View, Bumps Down) Skyworks Solutions, Inc. Phone 781 376-3000 Fax 781 376-3100 sales skyworksinc.com www.skyworksinc.com 201654 E Skyworks Proprietary and Confidential Information Products and Product Information are Subject to Change Without Notice July 1, 2109 1 DATA SHEET SE2600S WLAN SWITCH/LNA FEM Table 1. SE2600S Signal Descriptions Pin Name Description Pin Name Description 1 TX WLAN transmit port 7 GND Ground 2 GND Ground 8 BT Bluetooth port 3 VON LNA control signal 9 VC1 BT switch control pin 4 RX WLAN receive port 10 RFC RF common port (antenna) 5 VDD Positive power supply voltage 11 VC3 Transmit switch control pin 6 VC2 Receive switch control pin Table 2. SE2600S Absolute Maximum Ratings Parameter Symbol Minimum Maximum Units Supply voltage VDD 0 3.6 V DC input on control pins 0.5 VDD + 0.5 V Transmit input power, RFC terminated in 50 match PIN +27 dBm Operating temperature TA 40 +85 C Storage temperature TSTG 40 +150 C Note: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. CAUTION: Although this device is designed to be as robust as possible, Electrostatic Discharge (ESD) can damage this device. This device must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. The SE2600S ESD threshold level is 1000 VDC using Human Body Model (HBM) testing. Table 3. Recommended Operating Conditions Parameter Symbol Minimum Typical Maximum Units Supply voltage VDD 2.7 3.3 3.6 V Control voltage (relative to GND = 0 V) VCTL 0 VDD V Operating temperature TA 40 +25 +85 C The state of the SE2600S is determined by the logic provided in Electrical and Mechanical Specifications Table 8. The absolute maximum ratings of the SE2600S are provided in Table 2. The recommended operating conditions are specified in Table 3 and electrical specifications are provided in Tables 4 through 7. Skyworks Solutions, Inc. Phone 781 376-3000 Fax 781 376-3100 sales skyworksinc.com www.skyworksinc.com 2 July 1, 2019 Skyworks Proprietary and Confidential Information Products and Product Information are Subject to Change Without Notice 201654 E