RM058BV09774 Standexmeder

A Global Leader in the Design, Development, and Manufacture of Sensor and Magnetic Components Series Datasheet RM05-4A Reed Relays www.standexmeder.com RM05-4A Series Reed Relays Features: 4-Pole Low Profile SMD RF Relay Module, <40ps Rise Time for Switching Fast Pulses, BGA Applications: High Frequency Applications, Automated Test Equipment & Others Markets: Test and Measurement, Telecommunications & Others Part Description: RM05 - 0 X - S - 4 / 0 Nominal Contact QTY Contact Form Solder Balls Input Output Voltage 05 4 4A, 2A2B S 4 2, 4 Customer Options Switch Model Unit Contact Data 80/1 Rated Power (max.) 10 W Any DC combination of V&A not to exceed their individual max.s Switching Voltage (max.) 170 V DC or peak AC Switching Current (max.) 0.5 A DC or peak AC Carry Current (max.) 0.5 A DC or peak AC Contact Resistance (max.) 200 mOhm 0.5V & 50mA Breakdown Voltage (min.) 0.21 kVDC According to EN60255-5 Operating Time (max.) 0.1 ms Incl. Bounce Measured with w/ Nominal Voltage Release Time (max.) 0.02 ms Measured with no Coil Excitation Insulation Resistance (typ.) 1 GOhm Rh<45%, 100V Test Voltage Capacitance (typ.) 0.1 pF 10kHz across open Switch USA: +1.866.782.6339 salesusa standexmeder.com Version 01 Europe: +49.7731.8399.0 info standexmeder.com 27.01.2015 Asia: +86.21.37820625 salesasia standexmeder.com Modifications in the sense of technical progress are reserved. A Global Leader in the Design, Development, and Manufacture of Sensor and Magnetic Components Series Datasheet RM05-4A Reed Relays www.standexmeder.com Coil Data RM05-4A Reed Relay Contact Form 4A, 2A2B Unit Switch Model 80 Coil Voltage (nom.) 5 VDC Coil Resistance (typ.) 185 Ohm Pull-In Voltage (max.) 3.75 VDC Drop-Out Voltage (min.) 0.5 VDC Nominal Coil Power (typ.) 135 mW The Pull-In / Drop-Out Voltage and Coil Resistance will change at Rate of 0.4% per C Relay Data Module Characteristics Insertion Loss (typ.) Input/Output On request Voltage Standing Wave Ratio (typ.) Input/Output On request Life Test Data *Load increase reduces life expectancy of Reed Switches Isolation (typ.) Input/Output On request Rise Time (typ.) Input/Output On request Charateristics. Impedance (typ.) 0.5 On request Environmental Data Unit Shock Resistance (max.) 50 g 1/2 sine wave duration 11ms Vibration Resistance (max.) 10 g Operating Temperature -20 to 85 C Storage Temperature -35 to 125 C Soldering Temperature (max.) 220 C Handling & Assembly Instructions 5 sec. max. Switching inductive and/or capacitive loads create Glossary Contact Form voltage and/or current peaks, which may damage NO = Normally Open Contacts the relay. Protective circuits need to be used. Form A SPST = Single Pole Single Throw External magnetic fields needs to be taken into consideration, including a too high packing density. NC = Normally Closed Contacts Form B This may influence the relays electrical SPST = Single Pole Single Throw characteristics. Changeover Mechanical shock impacts e.g. dropping the relays Form C SPDT = Single Pole Double Throw may cause immediate or post-installation failure. Wave soldering: maximum 260/5 seconds. Reflow soldering: Recommendations given by the soldering paste manufacturer need to be considered as well as the temperature limits of other components/processes. USA: +1.866.782.6339 salesusa standexmeder.com Version 01 Europe: +49.7731.8399.0 info standexmeder.com 27.01.2015 Asia: +86.21.37820625 salesasia standexmeder.com Modifications in the sense of technical progress are reserved.