EV-VND7E050AJ STMicroelectronics

EV-VND7E050AJ Data brief VND7E050AJ evaluation board Features V Max transient supply voltage 40 V CC V Operating voltage range 4 to 28 V CC R Typ. on-state resistance (per Ch) 50 m ON Current limitation (typ) I 40 A LIMH Standby current (max) I 0.5 A STBY Minimum cranking supply voltage (V decreasing) V 2.85 V CC USD cranking Simple single IC application board dedicated for VND7E050AJ Provides electrical connectivity and thermal heat-sinking for easy prototyping General device features Double channel smart high-side driver with CurrentSense analog feedback Very low standby current Compatible with 3 V and 5 V CMOS outputs Extreme low voltage operation for deep cold cranking applications (compliant to LV124, revision 2013) Diagnostic functions Analog feedback of load current with high precision proportional current mirror Overload and short to ground (power limitation) indication Thermal shutdown indication Product status link OFF-state open-load detection EV-VND7E050AJ Output short to V detection CC Order code References Sense enable/disable Protections EV-VND7E050AJ EV-VND7E050AJ evaluation board Undervoltage shutdown Overvoltage clamp Load current limitation Self limiting of fast thermal transients Configurable latch-off on overtemperature or power limitation with dedicated fault reset pin Loss of ground and loss of V CC Reverse battery with external components Electrostatic discharge protection Application Automotive resistive, inductive and capacitive loads Protected supply for ADAS systems: radars and sensors Automotive headlamp DB4006 - Rev 1 - August 2019 www.st.com For further information contact your local STMicroelectronics sales office.EV-VND7E050AJ Description This board provides you an easy way to connect STMicroelectronics VIPower M0-7 technology into your existing system. The board comes pre-assembled with VND7E050AJ high-side driver. On board minimum set of electrical components (as for device datasheet recommendation) is enabling the user to directly connect the load, the power supply and the microcontroller without any additional effort in external component design and connection. The VND7E050AJ is a double channel high-side driver manufactured using ST proprietary VIPower technology and housed in PowerSSO-16 package. The device is designed to drive 12 V automotive grounded loads through a 3 V and 5 V CMOS- compatible interface and to provide protection and diagnostics. The device integrates advanced protective functions such as load current limitation, overload active management by power limitation and overtemperature shutdown with configurable latch-off. A FaultRST pin unlatches the output in case of fault or disables the latch-off functionality. A dedicated multifunction multiplexed analog output pin delivers sophisticated diagnostic functions including high precision proportional load current sense, supply voltage feedback and chip temperature sense, in addition to the detection of overload and short-circuit to ground, short to V and OFF-state open-load. A sense enable CC pin allows OFF-state diagnosis to be disabled during the module low-power mode as well as external sense resistor sharing among similar devices. Figure 1. Evaluation board schematic Vbat Vbat J1 C1 100nF In PullUP PGND J2 Vbat R UP1 R UP2 U1 J3 IN0 R1 15K 1 INPUT0 1 IN1 R2 15K 8 16 Out0 INPUT1 OUTPUT0 2 15 OUTPUT0 3 14 R3 15K OUTPUT0 4 FaultRST 2 13 In PullUP FaultRST OUTPUT0 5 R4 15K +5V 6 S EN 3 FaultRST SEn R5 15K 7 CurrentSense 7 12 Out1 CurrentSense CurrentSense OUTPUT1 8 11 S EN C3 OUTPUT1 9 1 10 SEL0 10nF R6 15K OUTPUT1 10 SEL0 5 9 SEL1 Rsense TP1 SEL0 OUTPUT1 11 SEL1 6 SEL1 12 IN0 1 R7 15K PGND 13 4 IN1 GND 14 TP2 PGND 15 PSS0-16 16 D1 R8 17 4K7 18 ES1DL CON18 PGND LED1 LED2 C4 C2 10nF 10nF R9 R10 PGND 2k2 2k2 J4 PGND PGND GADG300920191004FSR DB4006 - Rev 1 page 2/7 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 10 0 VBATT 1 2