2200-002003 Storm Interface

2200 Series Panel-mount Trackballs Rugged cursor control for industrial and hostile public environments 38mm panel-mount trackball Robust chassis designed to provide provides smooth, responsive and secure under-panel fixing for precise cursor control maximum resistance to hard use, abuse and vandalism Vandal resistant version features a stainless steel retention ring and a On-board encoder automatically coated steel ball (mirror finish) configures to provide either USB (10J BS EN 60068-2-75: 1997) or PS2 connectivity Robust version features a tough Two click keys (not supplied) phenolic resin ball (black) can be connected directly to the on-board encoder Sealed against the ingress of liquids & dust to IP65 when ball is USB and PS2 cables for stationary (IP54 when rotating) connection to host system are available separately o o Operating temp: -20 C (dry) to +60 C Storm Interface products include technology protected by international patents and design registration. www.storm-interface.com All rights reserved.Panel-mount trackballs for industrial and public environments These 38mm trackballs provide smooth, accurate and responsive cursor control in wet, dirty or aggressive environments. Each device automatically configures to provide USB or PS2 connectivity. Two selector (click) buttons (not supplied) can be configured to provide either left and right click functions or for both buttons to provide left click functions only. These trackballs can be installed as a flush mounted component in a control panel or equipment housing. Cables enabling connection to either USB or PS2 systems are supplied separately. The trackballs are constructed to ensure maximum resistance to hard use, abuse, and vandalism. 52.5 Overall Dimensions Panel Preparation (Vandal plate not shown) Details 60 Trackball o 38.0mm CONNECTOR CONNECTOR Panel Thickness: P1 P2 P3 1.5 3.0mm 1 2 3 4 5 6 1 2 3 4 5 6 M3 x 40mm studs (4off) 25 Connector Pinout Details The unit automatically selects either USB or PS/2 protocols on power-up. No re-setting of Pin Button PS2 / USB any DIP switches required. Connections Output If both buttons are required to be set as left click then a connection must be made between (P1) Connections pins on connector P2 using the jumper device (supplied). (P3) Please note that the TEST input is reserved for factory test only. On no account should a 1 0V D- / Data connection be made to this terminal. 2 Button 1 (left) D+ / Clock The Button inputs are pulled high to 5V within the unit. 3 0V Test Only Both rising and falling edges of this signal are debounced for 30ms. 4 Button 2 (right) Power +5V The Storm Trackball is designed to work with resident drivers and does not require 5 0V Ground 0V additional software to be loaded. 6 Button 3 (middle) Not used Electrical Environmental o o Supply Voltage 5.0V dc 10% Operating Temp -20 C (dry) to +60 C Switch Debounce 30ms rising/falling IP65 seal when ball stationary Supply Current 15mA maximum IP54 seal when ball rotating Resolution 150 pulses, 600 counts/revolution Humidity 95% Rh max, non-condensing Mechanical Material Tracking Force 50g nominal any direction Robust Trackball Phenolic Resin Ball Speed 250 rpm maximum Vandal Resistant Trackball Surface Treated Steel Operational Life 10 million revolutions (min) Seal Material PTFE with low friction fill o Mounting Angle within 45 from horizontal Vandal Plate Stainless Steel NB. Robust Version does not have Vandal Plate Installation Prepare plate with hole for o43.0mm bezel and M3 x 40mm studs on 52.5mm centres. Fit sealing gasket to trackball. Place trackball over studs. Place vandal plate over studs (VR version only). Secure with plain washers and Nyloc nuts. IMPORTANT: Max torque 40Ncm on nuts. Connect switches to connector P1. If reqd,fit jumper to enable both buttons as left click. Whilst every effort is made to ensure details Accessories x denotes packaging variant are correct at time of print, specifications are subject to change without notice. Stock No. Item 2200-00200 x Cable 2.5m PS2 2200-00300 x Cable 2.5m USB Storm is a trademark of Keymat Technology Ltd Storm Interface is a trading name of Keymat Technology Ltd 2200-00020 x Trackball Unit PS2 / USB Black Phenolic Ball UL File reference: E230121 003 Storm Interface products include Designed & produced by 2200-00030 x Trackball Unit PS2 / USB Coated Steel Ball 2200-LIT-01 Rev 4 technology protected by international patents NIK Design FM 39602 and design registration. All rights reserved. www.nikdesign.co.uk Nov 2008 43 52.5