ASSEMBLY P/N NO. OF CONTACT CUSTOMER APPROVAL NOTES: 1. FINISHED ASSEMBLIES AND LOOSE PARTS BAGGED. THIS DOCUMENT CONTAINS CONFIDENTIAL SF8980-9PG-5XX (9) 26 2. LABEL WITH CONXALL PART NUMBER, DATE CODE AND P/N BARCODE PLACED ON BAG INFORMATION PROPRIETARY TO CONXALL SF8980-10PG-5XX (10) 26 CORPORATION. ANY REPRODUCTION, 3. SEE DRAWING HPSFMISTD FOR HOLE PATTERNS DISCLOSURE, OR USE OF THIS 4. FOR FIELD INSTALLATION, SEE INSTRUCTION SHEET 2 OF 2. SF8980-11PG-5XX (11) 26 DOCUMENT /INFORMATION IS EXPRESSLY 5. ALL DIMENSIONS ARE REFERENCE EXCEPT THOSE WITH A TOLERANCE PROHIBITED UNLESS AUTHORIZED IN SF8980-12PG-5XX (12) 26 6. DIMENSIONS IN BRACKETS ARE IN MILLIMETERS WRITING BY CONXALL CORPORATION. 7. CRIMP CONTACT SUPPLIED UNASSEMBLED SF8980-13PG-5XX (13) 26 APPROVED BY: SF8980-14PG-5XX (14) 26 DATE: SF8980-15PG-5XX (15) 26 SF8980-16PG-5XX (16) 26 SF8980-17PG-5XX (17) 26 .750 SF8980-18PG-5XX (18) 26 19.1 (2) 4x3/8 IN SELF TAPPING SCREWS 520 = BACKSHELL WITH .220 5.6 GROMMET I.D. MAT L: STAINLESS STEEL 530 = BACKSHELL WITH .330 8.4 GROMMET I.D. CABLE STRAP MAT L: NYLON, BLACK .943 .770 24 1.429 .375 .997 19.6 .186.010 36.3 9.5 25.3 18 KEY KEY 1 INSERT, MALE 4.70.3 11 MAT L: PBT, BLACK 12 17 2 13 10 2.30 3 9 58.4 4 16 14 8 GROMMET INSULATOR TUBE 7 5 MAT L: RUBBER, BLACK MAT L: MYLAR 6 15 HOUSING MAT L: NICKEL PLATED BRASS WIRE VIEW BACKSHELL FACE VIEW HOUSING ADAPTER MAT L: NYLON, BLACK SF8980-18PG-5XX SHOWN SF8980-18PG-5XX SHOWN MAT L: NICKEL PLATED BRASS WASHER WITHOUT HARDWARE MAT L: NYLON (X) 26 PIN CONTACTS, CRIMP O-RING MAT L: GOLD PLATED COPPER ALLOY MAT L: SILICONE, RED SEE NOTE 7 COPPER TAPE 18 1 1 1 1 2.515 11 11 11 11 63.9 10 2 10 2 10 2 10 2 2 10 9 3 9 3 9 3 9 3 9 3 16 13 8 4 8 4 8 4 8 4 4 8 7 5 7 5 7 5 7 5 5 7 6 6 6 6 ASSEMBLED VIEW WIRE VIEW WIRE VIEW WIRE VIEW WIRE VIEW WIRE VIEW SF8980-9PG-5XX SF8980-10PG-5XX SF8980-11PG-5XX SF8980-12PG-5XX SF8980-13PG-5XX FOR CUSTOMER REFERENCE ONLY 18 18 18 18 1 1 1 1 1 11 11 11 11 11 12 12 17 12 17 12 17 MA 10-29-19 RELEASED PER PDR 17011 10 2 10 2 2 10 10 2 10 2 9-28-18 RES-79 CHANGED TO RES-78. O-RING 4290S REPLACES SF6290-1. A PNK 1-30-18 DRAWING CREATED PER PDR 17011 PNK 9 3 9 3 9 3 9 3 9 3 REV. INIT. DATE DESCRIPTION ORIG. DRAWN BY: DATE: ALL INFORMATION ILLUSTRATED IS 16 16 16 13 THE PROPERTY OFCONXALL 16 13 13 PNK 1-30-18 CORPORATION UNAUTHORIZED 4 8 4 DUPLICATION OR DISTRIBUTION OF CHECKED BY: 8 THIS DOCUMENT IS PROHIBITED. 8 8 8 4 7 4 601 E. WILDWOOD VILLA PARK, IL 60181 4 ALL UNITS ARE IN FEET, 5 5 7 6 6 5 6 INCHES, FRACTION OF INCHES 7 7 APPROVED BY: TITLE: 5 5 7 14 15 14 AND DECIMALS. CABLE-TO-CABLE ASSEMBLY 6 14 15 15 6 14 UNLESS OTHERWISE SPECIFIED (9-18) 26 PIN CONTACTS, CRIMP TOLERANCES: WIRE VIEW WIRE VIEW WIRE VIEW WIRE VIEW WIRE VIEW SCALE SIZE SHEET SHIELDED MINI-CON-X 3 PLACE DECIMALS .005 ANGLES 1 CUSTOMER: STANDARD PRODUCT SF8980-14PG-5XX SF8980-15PG-5XX SF8980-16PG-5XX SF8980-17PG-5XX SF8980-18PG-5XX NTS B 1 OF 2 FRACTIONS 1/16 FILE: DIRECTORY: REV PART RoHS COMPLIANT = CRITICAL CHARACTERISTIC SF8980-XPG-5XX NUMBER: FLAG PER SPEC. XXXX SF8980-XPG-5XX SLW A PART CUSTOMER PRINT SF8980-XPG-5XX NUMBER:CABLE CONDUCTORS CABLE SHIELD CABLE JACKET HOUSING ADAPTER .117 3 CABLE WIRING AND ASSEMBLY INSTRUCTIONS: INSULATOR TUBE STEP 1. SLIDE HOUSING ADAPTER, INSULATOR TUBE, AND BACKSHELL KIT, ONTO CABLE IN THE ORDER SHOWN. STEP 2. STRIP CABLE JACKET AND WIRES TO LENGTH. EXCESS CABLE SHIELD MUST BE TRIMMED OR WRAPPED AROUND WIRES. IF PRESENT, USE THE DRAIN WIRE TO WRAP THE CABLE SHIELD IN PLACE. STEP 3. CRIMP WIRES TO CONTACTS. STEP 3A. INSERT THE WIRED CONTACT INTO THE CAVITY AND FIRMLY PUSH THE CONTACT UNTIL IT LOCKS INTO PLACE. IN-LINE .125 GIVE A SLIGHT PULL ON THE WIRE TO INSURE THE CONTACT IS SEATED. THE CONTACT BARREL SHOULD CONNECTOR PROJECT BEYOND THE INSERT ACCORDING TO DIMENSION ABOVE. 3.2 DRAIN WIRE (IF PRESENT) BACKSHELL KIT .625 15.9 1.125 28.6 CONDUCTIVE TAPE WRAPPED ONTO INSULATOR TUBE STEP 4. THREAD HOUSING ADAPTER ONTO CONNECTOR AND TIGHTEN TO 5 LB-IN 0.56 N-m MINIMUM TORQUE. STEP 5. PEEL-OFF THE BACKING OF THE CONDUCTIVE TAPE AND WRAP IT AROUND THE INSULATOR AS SHOWN080 2 CONDUCTIVE TAPE WRAPPED TIGHTLY ONTO CABLE SHIELD STEP 6. SLIDE INSULATOR/CONDUCTIVE TAPE INTO THE BACK OF THE CONNECTOR. FORM FREE END OF CONDUCTIVE TAPE TIGHTLY ONTO THE SHIELD OF THE CABLE. STEP 7. SLIDE AND THREAD THE BACKSHELL KIT ONTO CONNECTOR. TIGHTEN TO 5 LB-IN 0.56 N-m MINIMUM TORQUE. STEP 8. TIGHTEN THE TWO BACKSHELL SCREWS TO SECURE THE CABLE IN THE BACKSHELL. COMPLETED ASSEMBLY MA 04-03-19 RELEASED PER PDR 17011 9-28-18 RES-79 CHANGED TO RES-78. O-RING 4290S REPLACES SF6290-1. A PNK PNK 1-30-18 DRAWING CREATED PER PDR 17011 REV. INIT. DATE DESCRIPTION ORIG. DRAWN BY: DATE: ALL INFORMATION ILLUSTRATED IS THE PROPERTY OFCONXALL PNK 1-30-18 CORPORATION UNAUTHORIZED DUPLICATION OR DISTRIBUTION OF CHECKED BY: THIS DOCUMENT IS PROHIBITED. 601 E. WILDWOOD VILLA PARK, IL 60181 ALL UNITS ARE IN FEET, INCHES, FRACTION OF INCHES APPROVED BY: TITLE: AND DECIMALS. CABLE-TO-CABLE ASSEMBLY UNLESS OTHERWISE SPECIFIED (9-18) 26 PIN CONTACTS, CRIMP TOLERANCES: SCALE SIZE SHEET SHIELDED MINI-CON-X 3 PLACE DECIMALS .005 ANGLES 1 CUSTOMER: STANDARD PRODUCT NTS B 2 OF 2 FRACTIONS 1/16 FILE: DIRECTORY: REV PART = CRITICAL CHARACTERISTIC SF8980-XPG-5XX NUMBER: FLAG PER SPEC. XXXX FILE NAME SLW A PART CUSTOMER PRINT SF8980-XPG-5XX NUMBER: