CURRENT SENSORS L34 D15 1/1 3 1508 Magnetic Proportion System L34S D15 SERIES RoHS Ta25, RL10k, Vcc15V SPECIFICATIONS Types Symbol L34S200D15 L34S300D15 L34S400D15 L34S500D15 L34S600D15 L34S800D15 L34S1T0D15 L34S1T2D15 L34S1T5D15 Spec If Primary norminal current 200A 300A 400A 500A 600A 800A 1000A 1200A 1500A 1 If max Saturation current 600A 900A 1200A 1500A 1800A 2400A 2500A 2500A 2500A Rated Output Voltage Vo 4V 0.040Vat If 2 Offset voltage Vof 0.020Vat If = 0A Output linearity without offset 0.5% at 0A1/2IfIf L Power supply voltage Vcc 12V 5% 15V 5% Icc 16mATYP 25mA Consumption current 3 tr 5s di/dt = 100A /s di/dt 90% of IfResponse time T VO 0.05%/Without TcVof Thermal drift of gain C T Vof 1.0mV/at If=0A Thermal drift of offset C Hysteresis error 10mVat 0A If 0A Insulation voltage Vd AC3000V, for 1minute Sensing current 0.5mA, inside of through hole terminal Insulation resistance R 500Mat DC500V inside of through hole terminal IS Ambient Operating temperature T 30 80 A Ambient storage temperature T 40 85 S 1 2 3 If the product of 800A or less operate at Vcc = 12V power supples, measuring range reduced to 2.5 x If. Offset voltage value is after removal of core hysteresis. Measurement condition : Primary conductor cross sectional area is as same as through hole, and penetration with 1turn in through hole. Please refer to the another sheet about conditions of UL Recognition. DIMENSIONS (mm) Lot No. L34S D15 Connector Types Manufacturer Part Number Old Part Number Plating of terminal L34SxxxD15 Standard 22-04-1041 5045-04A Sn Molex L34SxxxD15-A Build to Order 22-11-1041 5045-04AG Gold As for the product of a gold-plated connector, -A attaches to the end of the product name. Terminal number Weight Note 1 Vcc 15V 165g 1. Unless otherwise specified, 2 Vcc 15V tolerances shall be 0.5mm 3 Vout 4 GND 88 Closed loop Open loop Fluxgate system IntroductionCURRENT SENSORS Notices 1/1 3 1510 Important Notice 1. The content of this information is subject to change without 7. This product is not designed to resist radiation. prior notice for the purpose of improvements, etc. Ensure that Use in liquids such as water, oil, chemical solutions, or organic solvents, and use in locations where the product will you are in possession of the most up-to-date information when be exposed to such liquids. using this product. Use that involves exposure to direct sunlight, outdoor 2. This product is intended to be used in general electronics exposure, or dusty conditions. Use in locations where corrosive gases such as sea winds, applications (electric home appliances, business equipment, Cl2, H2S, NH3, SO2, or NO2, are present. (Some product information equipment, communication terminal equipment, improves durability) measuring devices, industrial equipment, and so on). This Use in environments with strong static electricity or product is neither intended nor warranted for use in following electromagnetic radiation. equipment or devices: Use that involves placing inflammable material next to the Special application (such as for medical devices, product. transportation equipment, traffic signal control equipment, Use of this product either sealed with a resin filling or coated fire and crime prevention equipment, aeronautics and with resin. Use of water or a water soluble detergent for flux cleaning. space devices, nuclear power control, fuel control, in- Use in locations where condensation is liable to occur. vehicle equipment, safety devices, and so on) in which 8. Do not use or otherwise make available the TAMUTA extremely high quality and high reliability is required, or if products or the technology described in this document for any the malfunction or failures of product could be cause loss of military purposes, including without limitation, for the design, human life, bodily injury. development, use, stockpiling or manufacturing of mass Tamura Corporation shall not be held responsible for any destruction weapons (e.g. nuclear, chemical, or biological damage incurred by customers or any third party when products weapons or missile technology products). When exporting are used in special application, unless specifically permitted in and re-exporting the products or technology described in this this document. document, you should comply with the applicable export control 3. Tamura Corporation constantly strives to improve quality and laws and regulations and follow the procedures required by reliability, but malfunction or failures are bound to occur with such laws and regulations including, without limitation, Japan some probability in current sensor. To ensure that failures do -Foreign Exchange and Foreign Trade Control Law and U.S.- not cause accidents resulting in injury or death, fire accidents, Export Administration Regulations. The TAMURA products social damage, and so on, users are to thoroughly verify the and related technology should not be used for or incorporated safety of their designs in devices and/or systems. into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or 4. The operation examples and circuit examples shown in this regulations. information are for reference purposes only, and Tamura Corporation disclaims all responsibility for any violations of 9. Please contact your TAMURA sales office for details as to industrial property rights, intellectual property rights and any environmental matters such as the RoHS compatibility of other rights owned by Tamura Corporation or third parties that Product. Please use TAMURA products in compliance with all these may entail. applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the 5. The circuit examples and part constants listed in these EU RoHS Directive. TAMURA assumes no liability for damages specifications are provided as reference for the verification or losses occurring as a result of your noncompliance with of characteristics. The user is to perform design, verification, applicable laws and regulations. and judgment under his or her own responsibility, taking into account the various conditions. 10. T AMURA assumes no liability for damages or losses incurred by you or third parties as a result of unauthorized use of TAMURA 6. The products are designed for use in environments where products. consumer electronics are commonly used. It is not designed for use in special environments such as listed below, and if such 11. This document and any information herein may not be use is considered, the user is to perform thorough safety and reproduced in whole or in part without prior written permission reliability checks under his/her responsibility. from TAMURA. 9