S22P 1/1 4 1209 CURRENT SENSORS Servo system / Voltage-output type S22P SERIES RoHS SPECIFICATIONS Ta=25C, RL=10k, Vcc=+5V Types S22P006S05 S22P015S05 S22P025S05 Spec If 6A 15A 25A Primary norminal current If max 18A 45A 75A Saturation current Vo Vof0.625Vat If Rated output voltage X G 0.625V0.010V (at If) Output voltage accuracy 1 Vof 2.5V0.050V (at If = 0 A) 2.5V0.020V (at If = 0 A) 2.5V0.015V (at If = 0 A) Offset voltage L 0.2%at If Output linearity Vcc 5V5% Power supply voltage Icc Typ.12.5mAIf=0A 37.5mAIf max Consumption current didt ( 90% of If) t r 1di/dts If /s Response time T CVO 0.05mV / (Without TcVof) Thermal drift of gain 10251.6mV / 10250.6mV / 10250.4mV / TcVof Thermal drift of offset 25850.8mV / 25850.3mV / 25850.2mV / V OH 0.5mV(at If = 0A If 0A) Hysteresis error AC3000V, 1(0.5mA) 1 2 Vd Insulation voltage AC3000V for 1 minute (Sensing current 0.5mA) Primary Sacondary 500M (at DC500V) 1 2 RIS Insulation resistance 500M (at DC500V) Primary Sacondary TA 1085 Ambient Operating temperature TS 25100 Ambient storage temperature 1 Offset voltage value is after removal of core hysteresis. UL *Please refer to the another sheet about conditions of UL Recognition. DIMENSIONS (mm) 0.8 22.2 0.7 5.08 2.54 2.54 10 12.7 7.66 5.08 7.6 1.9 Note 1 6 Unless otherwise specified, 2 5 IN OUT tolerances shall be 0.5mm 3 4 Weight: Unit is mm 8g typ 24 3.5 +5V *** G Lot No. Vout 5.5 0.5 23.5Notices 1/1 2 1412 CURRENT SENSORS Important Notice 1. 1. The content of this information is subject to change without prior notice for the purpose of improvements, etc. Ensure that you are in possession of the most up-to-date information when 2. using this product. 2. This product is intended to be used in general electronics appli- cations (electric home appliances, business equipment, infor- mation equipment, communication terminal equipment, meas- uring devices, industrial equipment, and so on). This product is neither intended nor warranted for use in following equipment or devices: Special application (such as for medical devices, transporta- tion equipment, traffic signal control equipment, fire and crime prevention equipment, aeronautics and space devic- 3. es, nuclear power control, fuel control, in-vehicle equipment, safety devices, and so on) in which extremely high quality and high reliability is required, or if the malfunction or fail- ures of product could be cause loss of human life, bodily injury. 4. Tamura Corporation shall not be held responsible for any dam- age incurred by customers or any third party when products are used in special application, unless specifically permitted in this 5. document. 3. Tamura Corporation constantly strives to improve quality and reliability, but malfunction or failures are bound to occur with 6. some probability in current sensor. To ensure that failures do not cause accidents resulting in injury or death, fire accidents, social damage, and so on, users are to thoroughly verify the safety of their designs in devices and/or systems. 4. The operation examples and circuit examples shown in this information are for reference purposes only, and Tamura Cor- poration disclaims all responsibility for any violations of industri- Cl2H2SNH3SO2NO2 al property rights, intellectual property rights and any other ( rights owned by Tamura Corporation or third parties that these may entail. 5. The circuit examples and part constants listed in these specifi- cations are provided as reference for the verification of charac- teristics. The user is to perform design, verification, and judg- ment under his or her own responsibility, taking into account 7. the various conditions. 8. 6. The products are designed for use in environments where consumer electronics are commonly used. It is not designed for use in special environments such as listed below, and if such use is considered, the user is to perform thorough safety and reliability checks under his/her responsibility. Use in liquids such as water, oil, chemical solutions, or organic solvents, and use in locations where the product will be exposed to such liquids.Use that involves exposure to direct sunlight, outdoor exposure, or dusty conditions. Use in locations where corrosive gases such as sea winds, Cl2, H2S, NH3, SO2, or NO2, are present. (Some product improves durability) Use in environments with strong static electricity or electro- magnetic radiation. Use that involves placing inflammable material next to the product. Use of this product either sealed with a resin filling or coat- ed with resin. Use of water or a water soluble detergent for flux cleaning. Use in locations where condensation is liable to occur. 7. This product is not designed to resist radiation. 8. This document and any information herein may not be repro- duced without prior written permission from TAMURA.