MESSRS : Product Drawing CUSTOMER S PRODUCT NAME: TDK PRODUCT NAME: DC/AC INVERTER UNIT CXA- L0605C-VxL TENTATIVE *Notice Product Drawing is not contract. This is only technical data. This technical data may change internal description without any notice. When you design final product please request us specification through our sales or distributors. After you receive the specification, the contract is effective on signature of the specification. TDK-Lambda Corporation PREPARED BY APPROVED BY AUTHORIZED BY April.12.2010 April.12.2010 April.12.2010 K.Negoro K.Yamaishi H.Masuoka DWG.No. CTR-3818-XPrecautionary Notes Regarding the Use of This Inverter When using this product, give due consideration to the precautionary notes described below and ensure a safe design. Inappropriate use may result in electric shock, injury or fire. Warning This product is subject to high voltage. Do not touch it while the power is on. Failing to do so may result in electric shock. Caution This product is designed for lighting Cold Cathode Fluorescent Lamps. Do not use it with any other load. Store this product under the conditions defined in the specification document. Do not store this product in an environment where dust, dirt or corrosive gas(salt,acid,base, etc.) is present. This product is subject to high voltage. If there is a possibility that the user may touch the product, provide a proper warning indication in order to draw the user s attention. This product is designed for use with general electronic equipment. If it is to be used with medical equipment that directly affects human life or for the control of transportation equipment to which passengers entrust their lives, provide thorough fail-safe measures. Consult us before using if this product is to be installed in a habitual vibration environment (vehicle, etc.). Avoid using this product under high temperatures or high humidity or in an environment in which dust, dirt or any corrosive gas (salt,acid,base, etc.) is present. Also,be careful not to allow the formation of dew condensation. It may result in damage or electric shock. If the product does not have a built-in protective circuit (circuit breaker, fuse, etc.), it is recommended that a fuse be used at the input stage to prevent the generation of smoke or fire in the event of a malfunction. Even when the product has a built-in protective circuit (circuit breaker, fuse, etc.), the circuit may not function properly due to inappropriate operating conditions or power-supply capacity. It is recommended that an appropriate protective circuit (circuit breaker, fuse, etc.) be provided separately from the built-in circuit. Use the product only within the specified input voltage, output power, output voltage and operating temperature ranges. Exceeding these values may result in damage, etc. Provide a measure for the prevention of surge voltage due to lightning, etc. Abnormal voltage may result in damage, etc. To prevent problems from occurring as a result of a short circuit in the high voltage section, be sure to take appropriate measures to prevent the entry of foreign substances into the inverter after it is installed. This product is not designed to provide resistance to radiation. In order to protect the inverter from vibration and shock, be sure to use all the mounting holes when installing the inverter. Ripples could be superimposed on the voltage and the current in the input source connected to the inverter , depending on the impedance in the input source, wiring, etc. When you select an input source, please check waveforms, etc on the final set. Please use all the mounting holes, because to defend the converter from vibration and impact. Handling Precautions This product uses thin wires. Observe the following precautions and handle it with care so as not to cause wire breakage. Broken wire may result in damage, etc. Do not stack multiple products on top of one another. Do not allow the product to come in contact with tools, etc. Do not apply excessive stress during installation. It may cause chipping and cracking,resulting in damage, etc. Provide clearance between the high-voltage section of this product and the frame body on which the product is installed and also the conductor section as on page 2 , 1 Outline . Do not use the product after it has been dropped because there is the possibility that components have been damaged. MATERIAL REMARK No. MATERIALS NAME QU PRODUCT NAME or MODEL,TITLE DC-AC INVERTER UNIT CXA-L0605C-VxL NAME OF DRAWING DRAWING No. PAGE TTTTDDDDKKKK----LLLLaaaammmmbbbbddddaaaa Product Drawing CTR-3818-X 1 TSB-08-01-05(00) form-6(A4) <The specifications may be changed without any notice.> T I TEN ATVE