ES2000
Flame-retardant, adhesive-lined heat-shrinkable
tubing (extended temperature range)
Adhesive-lined ES2000 heat- protection of wire splices and Because ES2000 tubing has a high
shrinkable tubing is specifically mechanically sensitive components. shrink ratio, only a few sizes are
designed to meet automotive industry The inner layer of the tubing is a needed to cover a wide range of
requirements for environmental unique hot-melt adhesive, specially splice and component diameters.
sealing and electrical insulation of formulated to adhere to all major ES2000 tubing dimensions have been
automotive wire splices, terminations, types of automotive wire insulation engineered to provide low-cost
and components. and to perform well at an extended sealing solutions on multiple-wire
temperature range. The adhesive splices (up to seven wires per side),
ES2000 tubing has an outer jacket forms an effective barrier against using standard Tyco Electronics
of radiation-crosslinked, semirigid automotive fluids and moisture, application equipment.
polyolefin. Flame-retardant and helping to protect the harness
mechanically tough, the jacket from the effects of corrosion and
provides strain relief and abrasion water wicking.
Temperature rating
Full recovery temperature: 135C
Continuous operating temperature: 40C to 130C
Specifications*
Type Raychem UL
ES2000 RT-1112 E85381
*When ordering, always specify latest issue.
Dimensions (millimeters/inches)
Expanded as supplied
W1 W2
Fully recovered
after heating
D d
W
Inside diameter (including core) Recovered wall thickness**
D (min.) d (max.) W W1 W2
Expanded Recovered after Minimum Minimum Minimum
Part number as supplied heating total wall jacket wall adhesive wall
ES2000-No.1 5.72 0.225 1.27 0.050 1.20 0.047 0.64 0.025 0.56 0.022
ES2000-No.2 7.44 0.293 1.65 0.065 1.52 0.060 0.76 0.030 0.76 0.030
ES2000-No.3 10.85 0.427 2.41 0.095 1.91 0.075 0.89 0.035 1.02 0.040
ES2000-No.4 17.78 0.700 4.45 0.175 2.41 0.095 1.04 0.041 1.37 0.054
**Wall thickness will be less if tubing recovery is restricted during shrinkage.
Ordering information
Color Black
Size selection Consult manufacturers recommended size selection guidelines.
Standard packaging Cut pieces. See reverse for information on standard cut lengths.
Marking Tubing will be marked with the number size (for example, ES-1, ES-2, ES-3, or ES-4).
Ordering description Specify product name, size, color, and cut length; for example, ES2000-No.2-0-50MM (0=Black). Specification values
Property Unit Requirement Method of test
Material Dimensions mm (inches) See reverse ASTM D 2671
Longitudinal change percent 0 to 10 ASTM D 2671
Tensile strength psi (MPa) 1500 (10.3) minimum ASTM D 2671
Ultimate elongation percent 250 minimum ASTM D 2671
Secant modulus at 2% psi (MPa) 20,000 (137) minimum ASTM D 2671
(expanded)*
Heat shock No dripping, flowing or ASTM D 2671
(4 hours at 225C/437F) cracking of outer jacket
Dynamic cut through pounds (kg) 30 (13.6) minimum ASTM D3032
12
Volume resistivity ohm-cm 1.0 X 10 minimum ASTM D 2671
Flammability Self-extinguishing See note below
within 30 seconds
Splice performance Current leakage microamps 0.25 maximum See note below
Room temperature flex test See note below
Current leakage microamps 0.25 maximum
Thermal shock See note below
Current leakage microamps 0.25 maximum
Low-temperature flexibility See note below
Dielectric withstand No breakdown
1 minute at 1000 V
Heat aging See note below
Current leakage microamps 0.25 maximum
Fluid immersion See note below
Current leakage microamps 0.25 maximum
Swell percent 50 maximum
Note: Consult Raychem RT-1112 for specific details about test procedures.
*Calculate based on wall thickness of jacket only.
Standard cut lengths
Part number Standard cut length Cut length tolerance
ES2000-No. 1 27 mm, 50 mm, 65 mm 1.5 mm
1220 mm 25.4 mm
ES2000-No. 2 27 mm, 50 mm, 65 mm 1.5 mm
1220 mm 25.4 mm
ES2000-No. 3 27 mm, 65 mm, 75 mm 1.5 mm
1220 mm 25.4 mm
ES2000-No. 4 27 mm, 75 mm, 90 mm 1.5 mm
1220 mm 25.4 mm
Raychem is a trademark of Tyco Electronics Corporation.
Users should independently evaluate the suitability of the product for their application.
Tyco Electronics Corporation
300 Constitution Drive Faraday Road 3816 Noborito, Tama-ku Asia Pacific Headquarters
Menlo Park, CA 94025-1164 Dorcan, Swindon, SN3 5HH Kawasaki, Kanagawa 214-8533 26 Ang Mo Kio, Industrial Park 2
USA United Kingdom Japan Singapore 569507
Tel:(800) 926-2425 (US & Canada) Tel: +44 1793 528171 Tel: +81 44 900 5102 Tel: +65 4866 151
Tel:+1 (650) 361-3860 (All other countries)
All information, including illustrations, is believed to be reliable. Users, however, should independently evaluate the suitability of each product for their application. Tyco Electronics Corporation makes
no warranties as to the accuracy or completeness of the information, and disclaims any liability regarding its use. Tyco Electronics Corporations only obligations are those in the Standard Terms and
Conditions of Sale for these products and in no case will Tyco Electronics Corporation be liable for any incidental, indirect, or consequential damages arising from the sale, resale, use, or misuse of the
product. Tyco Electronics Corporations Specifications are subject to change without notice. In addition, Tyco Electronics Corporation reserves the right to make changes in materials or processing
without notification to the Buyer which do not affect compliance with any applicable specification.
For more information about this product visit www.tycoelectronics.com
1990, 2002 Tyco Electronics Corporation Printed in USA 1654044 Revised 04/04