Application Specification CHAMP* Printed Circuit (PC) 114-6036 Board Mounted Connectors 16 SEP 11 Rev A All numerical values are in metric units with U.S. customary units in brackets . Dimensions are in millimeters and inches . NOTE PC board layouts are in inches only. Unless otherwise specified, dimensions have a tolerance of 0.13 .005 and angles have a tolerance of 2. Figures and illustrations are for identification only and are not drawn to scale. i 1. INTRODUCTION This specification covers the requirements for application of CHAMP pc board mounted connectors. The connectors are available in shielded and unshielded versions and are designed for right-angle-, vertical-, and edge-mount applications. The illustrations represent the available mounting options and show unshielded connectors for simplicity (plug and receptacle, shielded and unshielded are essentially the same). When corresponding with TE Connectivity Personnel, use the terminology provided in this specification to facilitate your inquiries for information. Basic terms and features of this product are provided in Figure 1. Vertical-Mount Connector 1.83 .072 Centerline (Typ) 2.16 .085 Centerline (Typ) Edge-Mount Contact Right-Angle Connector Tines (Typ) Mount Connector Figure 1 2. REFERENCE MATERIAL 2.1. Revision Summary Updated document to corporate requirements New logo 2.2. Customer Assistance Reference Product Base Part Number 552725 and Product Code 1252 are representative of the CHAMP pc board connector product line. Use of these numbers will identify the product line and expedite your inquiries through a service network established to help you obtain product and tooling information. Such information can be obtained through a local Representative or, after purchase, by calling PRODUCT INFORMATION at the number at the bottom of this page. 2.3. Drawings Customer Drawings for product part numbers are available from the service network. If there is a conflict between the information contained in the Customer Drawings and this specification or with any other technical documentation supplied, the information contained in the Customer Drawings takes priority. 2.4. Specification Product Specification 108-6078 provides product performance and test information. 2.5. Manuals Manual 402-40 is available from the service network. This manual provides information on various flux types and characteristics along with the commercial designation and flux removal procedures. A checklist is included to the manual as a guide for information on soldering problems. 2011 Tyco Electronics Corporation, a TE Connectivity Ltd. Company TOOLING ASSISTANCE CENTER 1-800-722-1111 This controlled document is subject to change. 1 of 8 All Rights Reserved PRODUCT INFORMATION 1-800-522-6752 For latest revision and Regional Customer Service, *Trademark visit our website at www.te.com LOC B TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners. 114-6036 2.6. Instructional Material Instruction Sheet 408-7672 provides right-angle and vertical-mount connector installation procedures. Instruction Sheet 408-3201 provides edge-mount connector installation procedures. Instruction Sheet 408-3160 provides attachment hardware information. Instruction Sheet 408-7564 provides mating cable connector information. 3. REQUIREMENTS 3.1. Safety Do not stack product shipping containers so high that the containers buckle or deform. 3.2. Storage A. Shelf Life The connectors should remain in the shipping containers until ready for use to prevent deformation to the contacts. The connectors should be used on a first in, first out basis to avoid storage contamination that could adversely affect performance. B. Chemical Exposure Do not store connectors near any chemical listed below as they may cause stress corrosion cracking in the contacts. Alkalies Ammonia Citrates Phosphates Citrates Sulfur Compounds Amines Carbonates Nitrites Sulfur Nitrites Tartrates 3.3. Printed Circuit Board A. Material The board should be composed of glass/epoxy material, use of less dimensionally stable material may present problems when inserting the components. B. Thickness The connectors may be installed on 1.57 to 3.18 mm .062 to .125 in. thick pc boards for vertical- and right- angle mount connectors and on 1.57 mm .062 in. thick PC Boards for edge-mount connectors. PC board thickness may vary depending upon application, however, terminal length becomes important for wave solder operations. A recommended minimum of 1.02 mm .040 in. terminal should protrude through the pc board. PC boards are divided into three categories, Class A, Class B, and Class C, depending on hole location tolerances (see Figure 2). HOLE LOCATION TOLERANCES mm in. RELATED BOARD SIZE CLASS A CLASS B CLASS C Greatest Dimension is Less 0.20 .008 0.10 .004 0.05 .002 Than 304.8 12.00 Greatest Dimension is Greater 0.20 .008 0.15 .006 0.10 .004 Than 304.8 12.00 Figure 2 C. PC Board Layout Typical pc board layouts are provided in Figure 3. Rev A 2 of 8