1-1414147-0 TE Connectivity

Automotive Relays Plug-in Maxi ISO Relays Power Relay F7 Pin assignment similar to ISO 7588 part 1 Customized versions on request 24VDC versions with contact gap >0.8mm Integrated components (e.g. resistor, diode) Customized marking/color Special covers (e.g. notches, release features, brackets) Typical applications Cross carline up to 70A for example: ABS control, cooling fan, energy management, engine control, glow plug, heated front screen, ignition, lamps: front, rear, fog light, main switch/supply relay. F134J a bw Contact Data Contact Data (continued) 6 Contact arrangement 1 form A, 1 form A, 1 form A, Mechanical endurance >1x10ops. 1 NO 1 NO 1 NO 1) Special high performance 24VDC version with contact gap >0.8mm. 2) The values apply to a resistive or inductive load with suitable spark suppression and Contact gap >0.8mm at maximum 14VDC for 12VDC or 28VDC for 24VDC load voltages. For a load current 1) Rated voltage 12VDC 24VDC 24VDC duration of maximum 3s for a make/break ratio of 1:10. Limiting continuous current 3) Current and time are compatible with circuit protection by a typical automotive fuse. 23C 70A 70A 70A Relay will make, carry and break the specified current. 85C 50A 50A 50A 4) See chapter Diagnostics of Relays in our Application Notes or consult the internet at Automotive Relays Plug-in Maxi ISO Relays Power Relay F7 (Continued) Insulation Data Other Data (continued) Initial dielectric strength Shock resistance (functional) 9) between open contacts 500V IEC 60068-2-27 (half sine) 6ms, min. 30g. rms between contact and coil 500V Drop test, free fall rms between adjacent contacts 500V IEC 60068-2-32 1m onto concrete rms Load dump test Terminal type plug-in, QC/ PCB ISO 7637-1 (12VDC), test pulse 5 V =+86.5VDC Cover retention s ISO 7637-2 (24VDC), test pulse 5 V =+200VDC pull force 150N s push force 200N Terminal retention Other Data pull force 150N EU RoHS/ELV compliance compliant push force 150N 8) 10) Protection to heat and fire according UL-94 HB or better resistance to bending 10N 10) Ambient temperature -40 to 125C force applied to side 10N Climatic cycling with condensation torque 0.3Nm EN ISO 6988 6 cycles, storage 8/16h Weight approx. 38g (1.3oz) Temperature cycling, Resistance to soldering heat THT IEC 60068-2-14, Nb 10 cycles, -40/+85C (5C/min) IEC 60068-2-20 260C, 10s Damp heat cyclic, Packaging unit IEC 60068-2-30, Db, Variant 1 6 cycles, upper air temp. 55C plug-in: 210 pcs. Damp heat constant, IEC 60068-2-3, Ca 56 days plug-in with bracket: 208 pcs. Category of environmental protection, PCB 315 pcs. IEC 61810 RTI dustproof 08) Refers to used materials. 09) No change in the switching state >10s. Valid for NC contacts, NO contact values Degree of protection, IEC 60529 IP54 (dustproof) significantly higher. Corrosive gas 10) Values apply 2mm from the end of the terminal. When the force is removed, the 3 3 IEC 60068-2-42 102cm /m SO , 10 days 2 terminal must not have moved by more than 0.3mm. 3 3 IEC 60068-2-43 10.3cm /m H S, 10 days 2 Vibration resistance (functional) 8) IEC 60068-2-6 (sine sweep) 10 to 500Hz, min. 5g Accessories For details see datasheet Connectors for Maxi ISO Relays Terminal Assignment NO NOR NOD 1 form A, NO 1 form A, NO with resistor 1 form A, NO with diode 85 87 85 87 85 87 86 30 86 30 86 30 Dimensions Power Relay F7 with quick connect terminals similar to ISO 8092-1 View of the terminals (bottom view) 25.9 0.3 15 0.1 6 0.4 5.3 0.1 4 0.2 TE1103-411 25.9 0.3 16 0.5 24.9 0.3 Measurement reference plane 4x 11 0.5 0.3 17 +1/-0.5 1.7 +0.2 6.3 0.1 0.8 0.05 1.2 0.05 9.5 0.1 2 Quick connect terminal similar to ISO 8092-1 TE1098-Y1 03-2020, Rev. 0320 Catalog and product specification according Catalog and product data is subject to the Catalog product data, Definitions section, www.te.com to IEC 61810-1 and to be used only together terms of the disclaimer and all chapters of application notes and all specifications are 2020 TE Connectivity. with the Definitions section. the Definitions section, available at subject to change.