ES2000 Flame-retardant, adhesive-lined heat-shrinkable tubing (extended temperature range) Adhesive-lined ES2000 heat- protection of wire splices and Because ES2000 tubing has a high shrinkable tubing is specifically mechanically sensitive components. shrink ratio, only a few sizes are designed to meet automotive industry The inner layer of the tubing is a needed to cover a wide range of requirements for environmental unique hot-melt adhesive, specially splice and component diameters. sealing and electrical insulation of formulated to adhere to all major ES2000 tubing dimensions have been automotive wire splices, terminations, types of automotive wire insulation engineered to provide low-cost and components. and to perform well at an extended sealing solutions on multiple-wire temperature range. The adhesive splices (up to seven wires per side), ES2000 tubing has an outer jacket forms an effective barrier against using standard Tyco Electronics of radiation-crosslinked, semirigid automotive fluids and moisture, application equipment. polyolefin. Flame-retardant and helping to protect the harness mechanically tough, the jacket from the effects of corrosion and provides strain relief and abrasion water wicking. Temperature rating Full recovery temperature: 135C Continuous operating temperature: 40C to 130C Specifications* Type Raychem UL ES2000 RT-1112 E85381 *When ordering, always specify latest issue. Dimensions (millimeters/inches) Expanded as supplied W1 W2 Fully recovered after heating D d W Inside diameter (including core) Recovered wall thickness** D (min.) d (max.) W W1 W2 Expanded Recovered after Minimum Minimum Minimum Part number as supplied heating total wall jacket wall adhesive wall ES2000-No.1 5.72 0.225 1.27 0.050 1.20 0.047 0.64 0.025 0.56 0.022 ES2000-No.2 7.44 0.293 1.65 0.065 1.52 0.060 0.76 0.030 0.76 0.030 ES2000-No.3 10.85 0.427 2.41 0.095 1.91 0.075 0.89 0.035 1.02 0.040 ES2000-No.4 17.78 0.700 4.45 0.175 2.41 0.095 1.04 0.041 1.37 0.054 **Wall thickness will be less if tubing recovery is restricted during shrinkage. Ordering information Color Black Size selection Consult manufacturers recommended size selection guidelines. Standard packaging Cut pieces. See reverse for information on standard cut lengths. Marking Tubing will be marked with the number size (for example, ES-1, ES-2, ES-3, or ES-4). Ordering description Specify product name, size, color, and cut length for example, ES2000-No.2-0-50MM (0=Black). Specification values Property Unit Requirement Method of test Material Dimensions mm (inches) See reverse ASTM D 2671 Longitudinal change percent 0 to 10 ASTM D 2671 Tensile strength psi (MPa) 1500 (10.3) minimum ASTM D 2671 Ultimate elongation percent 250 minimum ASTM D 2671 Secant modulus at 2% psi (MPa) 20,000 (137) minimum ASTM D 2671 (expanded)* Heat shock No dripping, flowing or ASTM D 2671 (4 hours at 225C/437F) cracking of outer jacket Dynamic cut through pounds (kg) 30 (13.6) minimum ASTM D3032 12 Volume resistivity ohm-cm 1.0 X 10 minimum ASTM D 2671 Flammability Self-extinguishing See note below within 30 seconds Splice performance Current leakage microamps 0.25 maximum See note below Room temperature flex test See note below Current leakage microamps 0.25 maximum Thermal shock See note below Current leakage microamps 0.25 maximum Low-temperature flexibility See note below Dielectric withstand No breakdown 1 minute at 1000 V Heat aging See note below Current leakage microamps 0.25 maximum Fluid immersion See note below Current leakage microamps 0.25 maximum Swell percent 50 maximum Note: Consult Raychem RT-1112 for specific details about test procedures. *Calculate based on wall thickness of jacket only. Standard cut lengths Part number Standard cut length Cut length tolerance ES2000-No. 1 27 mm, 50 mm, 65 mm 1.5 mm 1220 mm 25.4 mm ES2000-No. 2 27 mm, 50 mm, 65 mm 1.5 mm 1220 mm 25.4 mm ES2000-No. 3 27 mm, 65 mm, 75 mm 1.5 mm 1220 mm 25.4 mm ES2000-No. 4 27 mm, 75 mm, 90 mm 1.5 mm 1220 mm 25.4 mm Raychem is a trademark of Tyco Electronics Corporation. Users should independently evaluate the suitability of the product for their application. Tyco Electronics Corporation 300 Constitution Drive Faraday Road 3816 Noborito, Tama-ku Asia Pacific Headquarters Menlo Park, CA 94025-1164 Dorcan, Swindon, SN3 5HH Kawasaki, Kanagawa 214-8533 26 Ang Mo Kio, Industrial Park 2 USA United Kingdom Japan Singapore 569507 Tel:(800) 926-2425 (US & Canada) Tel: +44 1793 528171 Tel: +81 44 900 5102 Tel: +65 4866 151 Tel:+1 (650) 361-3860 (All other countries) All information, including illustrations, is believed to be reliable. Users, however, should independently evaluate the suitability of each product for their application. Tyco Electronics Corporation makes no warranties as to the accuracy or completeness of the information, and disclaims any liability regarding its use. Tyco Electronics Corporations only obligations are those in the Standard Terms and Conditions of Sale for these products and in no case will Tyco Electronics Corporation be liable for any incidental, indirect, or consequential damages arising from the sale, resale, use, or misuse of the product. Tyco Electronics Corporations Specifications are subject to change without notice. In addition, Tyco Electronics Corporation reserves the right to make changes in materials or processing without notification to the Buyer which do not affect compliance with any applicable specification. For more information about this product visit www.tycoelectronics.com 1990, 2002 Tyco Electronics Corporation Printed in USA 1654044 Revised 04/04