15647&6,21!+((6
( % &
(!$!% ! )) $ #, (8
2. Secure the nest die in the stationary jaw of the
tool frame using the die retaining screw. DO NOT
fully tighten the screw.
(56 ,(
3. Slowly cycle the tool, allowing the dies to align
themselves. Then, cycle the tool until the dies are
completely closed.
!&4(9
4. Securely tighten both die retaining screws.
2/(
!6$6,21$4:22/ 4$0(
18,/ ,(
$9
(56
(56 ,(
!&4(9
,( (6$,1,1*
2/(
!&4(95
Figure 1
28($%/(
$9
18,/ ,(
90Degree SnapLock Crimping Die Assembly
13386501 (shown in Figure 1) is designed to be
used with PROCRIMPER* III Hand Crimping Tool
Frame Assembly 3549401 to crimp the crimp claw of
the rightangle ferrule for coaxial snaplock cable
connectors onto coaxial cable. Refer to Instruction
Sheet 4089930 for information concerning the tool Figure 2
frame assembly.
Refer to 4084551 for cable strip length and
assembly information for the connector; for detailed
application requirements, refer to Application
Specification 11413010.
Reasons for reissue of this instruction sheet are
provided in Section 7, REVISION SUMMARY.
1. Crimp the straight portion of the ferrule
The die assembly consists of a nest die and an anvil according to 4088589.
die that when closed forms one crimping chamber.
2. Assemble the connector according to 4084551.
See Figure 1. Each die is secured in the tool by a
3. Place the crimp claw of the ferrule in the nest of
single screw (included with tool).
the anvil die so that the shoulder of the connector
butts against the edge of the die. See Figure 3.
!(( ,*74(
4. Bend the cable and insert it into the crimp claw,
while holding the connector at a 90 angle to the
1. Install the anvil die in the moveable jaw of the
nest.
tool frame. Align the screw hole of the die with the
screw hole of the tool frame, then secure the die 5. While holding the assembly together, cycle the
with the die retaining screw. DO NOT fully tighten tool until the dies have closed enough to hold the
the screw. assembly in place. !! +,5&21642//(2&70(16,557%-(&662&+$1*(
:&2 /(&6421,&5 24324$6,21 $44,5%74*
2)
// 16(41$6,21$/ ,*+65 (5(48( # 24/$6(564(8,5,21$1 (*,21$/ 75620(4!(48,&( /2*2$1":&2 /(&6421,&5$4(64$(0$4.5 8,5,62749(%5,6($6+++ *, & # *(&%! ) &$
4$(0$4. 6+(43427&65 /2*25 $1&203$1:1$0(575($4(6+(3423(46:2)6+(,44(53(&6,8(291(45
#" ( * )!% +$*$(# , &/
6. Allow the dies to close fully, crimping the ferrule 3. Inspect the crimping surfaces for flattened,
to the cable; then open fully so that the crimped chipped, worn, or cracked areas. If damage is
connector can be removed from the dies. evident, the dies must be replaced. Refer to
Section 6, REPLACEMENT.
) $& ! & (, !,
,.+$(# ($(#
$+# #$( #( !! # ($$!
The die assembly will perform correctly as long as:
(1) the product is correct for the die assembly, (2) the
tool has been adjusted correctly, and (3) the die
$## ($&
opening is correct. Refer to Figure 4.
$)! & #(
$
&% ! +
!
$## ($&
($ ! + &%
Figure 3
) $( ($ !
$(( (
Figure 4
1. Remove dust, moisture, and other contaminants
with a clean, soft brush, or a clean, soft, lintfree
cloth. DO NOT use any objects that could damage
the dies or tool.
Order die assemblies through your representative, or
2. Make sure that the proper die retaining screws call 18005265142, or send a facsimile of your
are properly secured. purchase order to 7179867605, or write to:
3. When the dies are not in use, store them in a
CUSTOMER SERVICE (038035)
clean, dry area.
TYCO ELECTRONICS CORPORATION
PO BOX 3608
(,!-$)(
HARRISBURG PA 171053608
The die assembly is inspected before shipment. It is
recommended that the dies be inspected immediately
upon arrival at your facility to ensure that the dies
have not been damaged during shipment.
Revisions to this instruction sheet include:
1. Remove all lubrication and accumulated film Updated document to corporate requirements
from the dies by immersing the dies in a suitable
Added tool frame assembly
commercial degreaser.
Added text to Sections 1 and 2
Modified Steps 2 and 3 of Section 3
2. Make certain that all die retaining screws and
Added Figure 2
die components are properly secured.
$ , $ ! (&$# $&%$& ( $# *