Signal Relays
AXICOM
P1 Relay V23026
n
Directly triggerable with TTL standard modules as ALS, HCT & ACT
n
Slim line 13.5x7.85mm (0.531x0.309)
n
Switching current 1 A
n
Bifurcated 1 form C (CO) contact
n
Immersion cleanable
AXICOM
n
High sensitivity results in low nominal power consumption,Telecom-, Signal and RF Relays 65 to 108-98009 Rev. E
130mW for monostable and 30 to 150mW for bistable (latching)
P1 V23026 Relay
n
Initial surge withstand voltage
2.5kV (2/10s) meets the Bellcore Requirement GR-1089
P1_THTSMD
1.5kV (10/160s) meets FCC Part 68
Contact Data
Typical applications
Automotive equipment, CAN bus, imobilizer, office equipment, measurement
Number of contacts and type 1 changeover contact
Z
and control equipment, medical equipment, safety equipment
Contact assembly Bifurcated contact
Contact material Palladium nickel, gold-rhodium covered
Approvals Coil Data
Limiting continuous current at max. ambient temperature 1 A
UL 508 File No. E 111441 Magnetic system polarized
Coil voltage range 3 to 24VDC
Technical data of approved types on request
Maximum switching current 1 A
other coil voltages on request
Maximum swichting voltage 125 Vdc
Operative range, IEC 61810 see coil operative range
150 Vac
Contact Data Max. coil temperature 85C
Contact arrangement 1 form C (CO) Thermal resistance <130K/W
Maximum switching capacity 30 W, 60 VA
Max. switching voltage 125VDC, 150VAC
Rated current 1A Coil versions, THT, monostable
Thermoelectric potential < 100 V
Limiting continuous current, 85C 1A Coil Rated Operate Release Coil Rated coil
Initial contact resistance / measuring condition: 10 mA / 20 mV < 50 m
Breaking capacity max. see max. DC load br eaking capacity code voltage voltage voltage resistance power
Contact material Palladium nickel, VDC VDC7 VDC 10% mW
min. min.
Electrical endurance at 12 V / 10 mA typ. 5 x 10 operations
gold-rhodium covered 006 3 2.25 0.3 137 66
7
at 6 V / 100 mA typ. 1 x 10 operations
Contact style bifurcated contact 001 5 3.75 0.5 370 68
4
at 30 V / 1000 mA typ. 1 x 10 operations
Min. recommended contact load 10mA at 20mV 005 9 6.75 0.9 1165 70
Initial contact resistance 50m at 10mA/20mV 002 12 9.00 1.2 2250 34
9
FrMechanical enduranceequency of operation without load 200 ops./s 004 24 typ. 10 operations18.00 2.4 4500 128
Operate/release time max. 2ms All figures are given for coil without pre-energization, at ambient temperature +23C.
UL contact ratings 30 Vdc / 1 A
Set/reset time max. 2ms
65 Vdc / 0.46 A
Bounce time max. 3ms Coil versions, SMT, monostable
150 Vac / 0.46 A
Electrical endurance Coil Rated Operate Release Coil Rated coil
6
at 12V/10mA typ. 50x10 operations code voltage voltage voltage resistance power
AXICOM
6
at 6V/100mA typ. 10x10 operations VDC VDC VDC 10% mW
min. min.
Telecom-, Signal and RF Relays
108-98009 Rev. E
3
at 30V/1000mA typ. 10x10 operations 026 3 2.25 0.3 113 80
Contact ratings 021 5 3.75 0.5 313 80
P1 V23026 Relay
UL contact ratings 30VDC/1A 025 9 6.75 0.9 1015 80
65VDC/0.46A 022 12 9.00 1.2 1800 80
150VAC/0.46A 024 24 18.00 2.4 4500 128
Max. DC Load Breaking Capacity
9
All figures are given for coil without pre-energization, at ambient temperature +23C.
Mechanical endurance typ. 10 operations Coil Operating Range
Max. DC load breaking capacity Coil operative range, monostable DC coil
U = Nominal coil voltage
nom
65 mW U = Upper limit of the operative range of
max.
130 mW
the coil voltage (limiting voltage)
when coils are continously energized
Umax. at 0 A
U = Lower limit of the operative range of
Umax. at 0 A Umax. at - 1 A op. min.
the coil voltage (reliable operate
voltage)
U = Lower limit of the operative range of
rel. min.
the coil voltage (reliable release
voltage)
Unom. nominal coil voltage
Uop. min.
Urel. min.
Ambient Temperature [C]
1
65 mW Latching
Umax. - 5 % coil duty at 1 A
02-2012, Rev. 0212 Datasheets and product specification Datasheets and product data is subject to the Datasheets, product data, Definitions sec-
32 mW Latching
www.te.com according to IEC 61810-1 and to be used terms of the disclaimer and all chapters of tion, application notes and all specifications
2011 Tyco Electronics Corporation, only together with the Definitions section. the Definitions section, available at are subject to change.
a TE Connectivity Ltd. company Signal Relays
AXICOM
P1 Relay V23026 (Continued)
Coil data (continued) Insulation Data
Initial dielectric strength
Coil versions, THT and SMT, bistable 2 coils between open contacts 500V
rms
Coil Rated Set Reset Coil Rated coil between contact and coil 1500V
rms
code voltage voltage voltage resistance power Initial surge withstand voltage
VDC VDC VDC 10% mW between contact and coil 2500V
106 3 2.25 2.25 130 69 Capacitance
101 5 3.75 3.75 390 64 between open contacts max. 5pF
105 9 6.75 6.75 1200 68 between contact and coil max. 6pF
102 12 9.00 9.00 1500 96 Clearance/creepage
1)
24 between contact and coil 0.75mm
All figures are given for coil without pre-energization, at ambient temperature +23C.
between adjacent contacts 0.75mm
Coils I and II are identical.
1)
A nominal voltage of 24VDC is feasible with a 12VDC coil with a series resistor (1500)
RF Data
Isolation at 100MHz/900MHz -30.0dB/-18.0dB
Coil data (continued) Insertion loss at 100MHz/900MHz -0.12dB/-1.9dB
Voltage standing wave ratio (VSWR)
AXICOM
Coil versions, THT, bistable 1 coil at 100MHz/900MHz 1.06/1.75
Telecom-, Signal and RF Relays 108-98009 Rev. E
Coil Rated Set Reset Coil Rated coil
code voltage voltage voltage resistance power
P1 V23026 Relay
VDC VDC VDC 10% mW Other Data
056 3 2.25 -2.25 300 30 Material compliance: EU RoHS/ELV, China RoHS, REACH, Halogen content
051 5 3.75 -3.75 740 34 refer to the Product Compliance Support Center at
057 9 6.75 -6.75 2160 38
www.te.com/customersupport/rohssupportcenter
Coil Operating Range
052 12 9.00 -9.00 4500 32 Ambient temperature -40 to +85C
054 24 18.00 -18.00 4500 128 Category of environmental protection,
U = Nominal coil voltage
nom
IEC 61810 RT III - immersion cleanable
65 mW U V ibration r = esistance (functional)Upper limit of the operative range of 20g, 200 to 2000Hz
max.
130 mW
the coil voltage (limiting voltage) 40g, 10 to 200Hz
Coil data (continued) Shock resistance (functional)
when coils are continously energized
Umax. at 0 A
IEC 60068-2-27 (half sine) 50 g
U = Lower limit of the operative range of
Coil versions, SMTUmax. at 0 , bistable 1 coilA Umax. at - 1 A op. min.Terminal type PCB terminals and SMT terminals
the coil voltage (reliable operate
Coil Rated Set Reset Coil Rated coil Weight max. 2g
voltage)
code voltage voltage voltage resistance power Resistance to soldering heat THT
VDC VDC VDC 10% mW IEC 60068-2-20 265 C/10s
U = Lower limit of the operative range of
rel. min.
051 5 3.75 -3.75 740 34 Resistance to soldering heat SMT
the coil voltage (reliable release
052 12 9.00 -9.00 4500 32 IEC 60068-2-58 see reflow profile
voltage)
A nominal voltage of 24V is feasible with a 12V coil with a series resitor (4500) Moisture sensitive level, JEDEC J-Std-020D MSL3
Unom. nominal coil voltage
Other coil voltages on request Washing not recommended
All figures are given for coil without pre-energization, at ambient temperature +23C.
Ultrasonic cleaning possible
Coils I and II are identical. Uop. min.
Packaging unit
Urel. min.
THT 2000 pcs.
SMT 2400 pcs.
Ambient Temperature [C]
Coil operative range, bistable
U upper limit of the operative range of the coil voltage (limiting voltage) when coils are
max
65 mW Latching
Umax. - 5 % coil duty at 1 A
32 mW Latching
Umax. - 100 % coil duty at 0 A
Umax. - 5 % coil duty at 0 A
Unom. nominal coil voltage
Uset min.
Ambient Temperature [C]
continuously energized.
U lower limit of the operative range of the coil voltage (reliable operate voltage).
op min
U lower limit of the operative range of the coil voltage (reliable release voltage).
rel min
2
02-2012, Rev. 0212 Datasheets and product specification Datasheets and product data is subject to the Datasheets, product data, Definitions sec-
www.te.com according to IEC 61810-1 and to be used terms of the disclaimer and all chapters of tion, application notes and all specifications
2011 Tyco Electronics Corporation, only together with the Definitions section. the Definitions section, available at are subject to change.
a TE Connectivity Ltd. company